From f237e1620365448294baa9f901b3f990cea3bc6f Mon Sep 17 00:00:00 2001 From: Theo Arends <11044339+arendst@users.noreply.github.com> Date: Tue, 11 Nov 2025 17:48:42 +0100 Subject: [PATCH] Increase wait for Reset complete in commission --- tasmota/include/xdrv_75_dali.h | 954 +++++++++++++++++++ tasmota/tasmota_xdrv_driver/xdrv_75_dali.ino | 396 +++----- 2 files changed, 1062 insertions(+), 288 deletions(-) create mode 100644 tasmota/include/xdrv_75_dali.h diff --git a/tasmota/include/xdrv_75_dali.h b/tasmota/include/xdrv_75_dali.h new file mode 100644 index 000000000..e9c100441 --- /dev/null +++ b/tasmota/include/xdrv_75_dali.h @@ -0,0 +1,954 @@ +/* + xdrv_75_dali.h - DALI support for Tasmota + + SPDX-FileCopyrightText: 2025 Theo Arends + + SPDX-License-Identifier: GPL-3.0-only +*/ + +#ifdef USE_DALI + +#ifndef _XDRV75_DALI_H_ +#define _XDRV75_DALI_H_ + +/*-------------------------------------------------------------------------------------------*\ + * DALI Address types - Send as first byte +\*-------------------------------------------------------------------------------------------*/ + +// Address types - Send as first byte +#define DALI_SHORT_ADDRESS0 0x0000 // 0b00000000 0 - First short address +#define DALI_SHORT_ADDRESS1 0x0002 // 0b00000010 1 - Next short address + // ... +#define DALI_SHORT_ADDRESS63 0x007E // 0b01111110 63 - Last short address +#define DALI_GROUP_ADDRESS0 0x0080 // 0b10000000 0 - First group address +#define DALI_GROUP_ADDRESS1 0x0082 // 0b10000010 1 - Next group address + // ... +#define DALI_GROUP_ADDRESS15 0x009E // 0b10011110 15 - Last group address +#define DALI_BROADCAST_DP 0x00FE // 0b11111110 254 - Broadcast address + +/*-------------------------------------------------------------------------------------------*\ + * DALI Commands for IEC62386 part 102 = Control gears - Send as first byte +\*-------------------------------------------------------------------------------------------*/ + +// Special commands - Send as first byte +#define DALI_102_TERMINATE 0x00A1 // 256 - All special mode processes (like DALI_102_INITIALISE) shall be terminated. +#define DALI_102_SET_DTR0 0x00A3 // 257 - Stores the data XXXX XXXX to the Data Transfer Register (Data Transfer Register 0). + // This is a broadcast command to set the value of the DTR0 register. +#define DALI_102_INITIALISE 0x01A5 // 258 REPEAT - Sets the ballast to the INITIALISE status for 15 minutes. Commands 167 to 189 are enabled only for a ballast in this status. + // This command shall start or re-trigger a timer for 15 minutes; the addressing commands 167..189 shall only be processed within this period. + // All other commands shall still be processed during this period. + // This time period shall be aborted with the "DALI_102_TERMINATE" command. + // Ballasts shall react as follows: + // - if broadcast is True then all ballasts shall react + // - if broadcast is False and address is None then ballasts without a short address shall react + // - if broadcast is False and address is an integer 0..63 then ballasts with the address supplied shall react +#define DALI_102_RANDOMISE 0x01A7 // 259 REPEAT - Generates a random address. + // The ballast shall generate a new 24-bit random address. The new random address shall be available within a time period of 100ms. +#define DALI_102_COMPARE 0x00A9 // 260 - Is the random address smaller or equal to the search address? + // The ballast shall compare its 24-bit random address with the combined search address stored in SearchAddrH, SearchAddrM and SearchAddrL. + // If its random address is smaller or equal to the search address and the ballast is not withdrawn then the ballast shall generate a query "YES". +#define DALI_102_WITHDRAW 0x00AB // 261 - Excludes ballasts for which the random address and search address match from the Compare process. + // The ballast that has a 24-bit random address equal to the combined search address stored in SearchAddrH, SearchAddrM and SearchAddrL + // shall no longer respond to the compare command. + // This ballast shall not be excluded from the initialisation process. +#define DALI_102_RESERVED173 0x00AD // 262 - [Reserved] +#define DALI_102_PING 0x00AF // 263 - DALI-2 Ignores in the ballast. + // Transmitted at 10 minute intervals by single master application controllers (that cannot perform collision detection) to indicate their presence. + // Ignored by control gear. +#define DALI_102_SEARCHADDRH 0x00B1 // 264 - Specifies the higher 8 bits of the search address. +#define DALI_102_SEARCHADDRM 0x00B3 // 265 - Specifies the middle 8 bits of the search address. +#define DALI_102_SEARCHADDRL 0x00B5 // 266 - Specifies the lower 8 bits of the search address. +#define DALI_102_PROGRAM_SHORT_ADDRESS 0x00B7 // 267 - The ballast shall store the received 6-bit address (AAA AAA) as a short address if it is selected. + // It is selected if: + // - the ballast's 24-bit random address is equal to the address in SearchAddrH, SearchAddrM and SearchAddrL + // - physical selection has been detected (the lamp is electrically disconnected after reception of command PhysicalSelection()) + // If address is 255 ("MASK") then the short address shall be deleted. +#define DALI_102_VERIFY_SHORT_ADDRESS 0x00B9 // 268 - Is the short address AAA AAA? + // The ballast shall give an answer 255 ("YES") if the received short address is equal to its own short address. +#define DALI_102_QUERY_SHORT_ADDRESS 0x00BB // 269 - What is the short address of the ballast being selected? + // The ballast shall send the short address if the random address is the same as the search address or the ballast is physically selected. + // The answer will be in the format (address<<1)|1 if the short address is programmed, or "MASK" (0xff) if there is no short address stored. +#define DALI_102_PHYSICAL_SELECTION 0x00BD // 270 - not DALI-2 Sets the ballast to Physical Selection Mode and excludes the ballast from the Compare process. (Excluding IEC62386-102ed2.0) +#define DALI_102_RESERVED191 0x00BF // 271 - [Reserved] + +// Extending special commands - Send as first byte +#define DALI_102_ENABLE_DEVICE_TYPE_X 0x00C1 // 272 - Adds the device XXXX (a special device). + // This command shall be sent before an application extended command. + // This command can be processed without the use of the Initialise() command. + // This command shall not be used for device type 0. +#define DALI_102_SET_DTR1 0x00C3 // 273 - Stores data XXXX into Data Transfer Register 1. + // This is a broadcast command to set the value of the DTR1 register. +#define DALI_102_SET_DTR2 0x00C5 // 274 - Stores data XXXX into Data Transfer Register 2. + // This is a broadcast command to set the value of the DTR2 register. +#define DALI_102_WRITE_MEMORY_LOCATION 0x00C7 // 275 - Write data into the specified address of the specified memory bank. (There is BW) (DTR(DTR0)：address, DTR1：memory bank number) + // This instruction will be ignored if the addressed memory bank is not implemented, or writeEnableState is DISABLED. + // If the instruction is executed then the control gear will write data into the memory location identified by DTR0 in bank DTR1 and return data as an answer. + // If the location is not implemented, above the last accessible location, locked or not writeable, the answer will be NO (-1). + // If the location addressed is below 0xff, then DTR0 will be incremented by 1. +#define DALI_102_WRITE_MEMORY_LOCATION_NO_REPLY 0x00C9 // 276 - DALI-2 Write data into the specified address of the specified memory bank. (There is no BW) (DTR(DTR0)：address, TR1：memory bank number) + // This instruction will be ignored if the addressed memory bank is not implemented, or writeEnableState is DISABLED. + // If the instruction is executed then the control gear will write data into the memory location identified by DTR0 in bank DTR1 + // If the location is not implemented, above the last accessible location, locked or not writeable, the answer will be NO (-1). + // If the location addressed is below 0xff, then DTR0 will be incremented by 1. +#define DALI_102_RESERVED277 0x00CB // 277 - [Reserved] + // ... +#define DALI_102_RESERVED349 0x00FD // 349 - [Reserved] + +/*-------------------------------------------------------------------------------------------*\ + * DALI Commands for IEC62386 part 102 = Control gears - Send as second byte +\*-------------------------------------------------------------------------------------------*/ + +// Control commands - Send as second byte without repeat +#define DALI_102_OFF 0x0000 // 0 - Turns off lighting (without fade). +#define DALI_102_UP 0x0001 // 1 - Increases the lighting control level for 200 ms according to the Fade rate. + // No change if the arc power output is already at the "MAX LEVEL". + // If this command is received again while it is being executed, the execution time shall be re-triggered. + // This command shall only affect ballasts with burning lamps. + // No lamp shall be ignited with this command. +#define DALI_102_DOWN 0x0002 // 2 - Decreases the lighting control level for 200 ms according to the Fade rate. + // No change if the arc power output is already at the "MIN LEVEL". + // If this command is received again while it is being executed, the execution time shall be re-triggered. + // Lamp shall not be switched off via this command. +#define DALI_102_STEP_UP 0x0003 // 3 - Increments the lighting control level (without fade). + // No change if the arc power output is already at the "MAX LEVEL". + // This command shall only affect ballasts with burning lamps. No lamp shall be ignited with this command. +#define DALI_102_STEP_DOWN 0x0004 // 4 - Decrements the lighting control level (without fade). + // No change if the arc power output is already at the "MIN LEVEL". + // Lamps shall not be switched off via this command. +#define DALI_102_RECALL_MAX_LEVEL 0x0005 // 5 - Maximizes the lighting control level to "MAX LEVEL" (without fade). + // If the lamp is off it shall be ignited with this command. +#define DALI_102_RECALL_MIN_LEVEL 0x0006 // 6 - Minimizes the lighting control level to "MIN LEVEL" (without fade) + // If the lamp is off it shall be ignited with this command. +#define DALI_102_STEP_DOWN_AND_OFF 0x0007 // 7 - Decrements the lighting control level and turns off lighting if the level is at the minimum (without fade). +#define DALI_102_ON_AND_STEP_UP 0x0008 // 8 - Increments the lighting control level and turns on lighting if lighting is off (with fade). +#define DALI_102_DIRECT_ARC_POWER_CONTROL 0x0009 // 9 - Enable DAPC Sequence + // Indicates the start of a command iteration of DAPC(level) commands. + // The control gear shall temporarily use a fade time of 200ms while the command iteration is active independent of the actual fade/extended fade time. + // The DAPC sequence shall end if 200ms elapse without the control gear receiving a DAPC(level) command. + // The sequence shall be aborted on reception of an indirect arc power control command. + // value 0 - Off + // value minLevel...maxLevel + // value 255 - Retain current level +#define DALI_102_GO_TO_LAST_ACTIVE_LEVEL 0x000A // 10 - DALI-2 Adjusts the lighting control level to the last light control level according to the Fade time. +#define DALI_102_CONTINUOUS_UP 0x000B // 11 - DALI-2 Dim up using the set fade rate. + // TargetLevel shall be set to maxLevel and a fade shall be started using the set fade rate. The fade shall stop when maxLevel is reached. +#define DALI_102_CONTINUOUS_DOWN 0x000C // 12 - DALI-2 Dim down using the set fade rate. + // targetLevel shall be set to minLevel and a fade shall be started using the set fade rate. The fade shall stop when minLevel is reached. +#define DALI_102_RESERVED13 0x000D // 13 - [Reserved] +#define DALI_102_RESERVED14 0x000E // 14 - [Reserved] +#define DALI_102_RESERVED15 0x000F // 15 - [Reserved] +#define DALI_102_GO_TO_SCENE0 0x0010 // 16 - Adjusts the lighting control level for Scene XXXX according to the fade time. + // If the ballast does not belong to this scene, the arc power level remains unchanged. + // If the lamp is off, it shall be ignited with this command. + // If the value stored for this scene is zero and the lamp is lit then the lamp shall be switched off by this command after the fade time. + // ... +#define DALI_102_GO_TO_SCENE15 0x001F // 31 - Adjusts the lighting control level for Scene XXXX according to the fade time. + +// Configuration commands - Send as second byte with repeat +#define DALI_102_RESET 0x0020 // 32 - The variables in the persistent memory shall be changed to their reset values. + // It is not guaranteed that any commands will be received properly within the next 300ms by a ballast acting on this command. +#define DALI_102_STORE_ACTUAL_LEVEL_IN_DTR0 0x0021 // 33 - Store actual arc power level in the DTR (DTR0) without changing the current light intensity. +#define DALI_102_SAVE_PERSISTENT_VARIABLES 0x0022 // 34 - DALI-2 Saves a variable in nonvolatile memory (NVM). + // All variables identified as non-volatile shall be stored to non-volatile memory. + // The control gear might not react to commands for up to 300ms after reception of this command. + // This command is recommended to be used typically after commissioning. +#define DALI_102_SET_OPERATING_MODE 0x0023 // 35 - DALI-2 Set operatingMode to DTR0. + // If DTR0 does not correspond to an implemented operating mode, the command shall be ignored. +#define DALI_102_RESET_MEMORY_BANK 0x0024 // 36 - DALI-2 Reset Memory Bank according to DTR0 + // If DTR0 = 0 then all implemented and unlocked memory banks except memory bank 0 shall be reset. + // In all other cases, the memory bank identified by DTR0 will be reset provided it is implemented and unlocked. + // This command may cause control gear to react improperly to commands for up to 10s. +#define DALI_102_IDENTIFY_DEVICE 0x0025 // 37 - DALI-2 Starts the identification state of the device. Start or restart a 10s timer. + // While the timer is running the device will run a procedure to enable an observer to distinguish the device from other devices in which it is not running. + // This procedure is manufacturer-dependent. + // Identification will be stopped immediately upon reception of any command other than Initialise, RecallMinLevel, RecallMaxLevel or IdentifyDevice. +#define DALI_102_RESERVED38 0x0026 // 38 - [Reserved] + // ... +#define DALI_102_RESERVED41 0x0029 // 41 - [Reserved] +#define DALI_102_SET_MAX_LEVEL 0x002A // 42 - Specifies the DTR data as the maximum lighting control level (maxLevel or "MAX LEVEL"). +#define DALI_102_SET_MIN_LEVEL 0x002B // 43 - Specifies the DTR data as the minimum lighting control level (minLevel or "MIN LEVEL"). + // If this value is lower than the "PHYSICAL MIN LEVEL" of the ballast, then store the "PHYSICAL MIN LEVEL" as the new "MIN LEVEL". +#define DALI_102_SET_SYSTEM_FAILURE_LEVEL 0x002C // 44 - Specifies the DTR data as the "SYSTEM FAILURE LEVEL". +#define DALI_102_SET_POWER_ON_LEVEL 0x002D // 45 - Specifies the DTR data as the "POWER ON LEVEL". +#define DALI_102_SET_FADE_TIME 0x002E // 46 - Specifies the DTR data as the "FADE TIME" in seconds. + // Formula T=0.5(sqrt(pow(2,DTR))) seconds + // With DTR0 in the range 1..15. If DTR0 is 0 then the extended fade time will be used. + // The fade time specifies the time for changing the arc power level from the actual level to the requested level. + // In the case of lamp off, the preheat and ignition time is not included in the fade time. + // The new fade time will be used after the reception of the next arc power command. + // If a new fade time is set during a running fade process, the running fade process is not affected. + // value 0 - < 0.707 s + // value 1 - 0.707 s + // value 2 - 1.000 s + // value 3 - 1.414 s + // value 4 - 2.000 s + // value 5 - 2.828 s + // value 6 - 4.000 s + // value 7 - 5.657 s + // value 8 - 8.000 s + // value 9 - 11.314 s + // value 10 - 16.000 s + // value 11 - 22.627 s + // value 12 - 32.000 s + // value 13 - 45.255 s + // value 14 - 64.000 s + // value 15 - 90.510 s +#define DALI_102_SET_FADE_RATE 0x002F // 47 - Specifies the DTR data as the "FADE RATE" in steps per second. + // Formula F = 506/(sqrt(pow(2,DTR))) steps/s + // With DTR in the range 1..15. + // The new fade time will be used after the reception of the next arc power command. + // If a new fade time is set during a running fade process, the running fade process is not affected. + // value 0 - not permitted + // value 1 - 357.796 steps/s + // value 2 - 253.000 steps/s + // value 3 - 178.898 steps/s + // value 4 - 126.500 steps/s + // value 5 - 89.449 steps/s + // value 6 - 63.250 steps/s + // value 7 - 44.725 steps/s + // value 8 - 31.625 steps/s + // value 9 - 22.362 steps/s + // value 10 - 15.813 steps/s + // value 11 - 11.181 steps/s + // value 12 - 7.906 steps/s + // value 13 - 5.591 steps/s + // value 14 - 3.953 steps/s + // value 15 - 2.795 steps/s +#define DALI_102_SET_EXTENDED_FADE_TIME 0x0030 // 48 - DALI-2 Specifies the DTR data as the Extended Fade Time. + // If DTR0 > 0x4f then extendedFadeTimeBase and extendedFadeTimeMultiplier are both set to 0. + // Otherwise, extendedFadeTimeBase will be set to DTR0[3:0] and extendedFadeTimeMultiplier will be set to DTR0[6:4]. + // If a new fade time is set during a running fade process, the running fade process is not affected. + // bit 0..3 - value 0..15 (E_DALIExtendedFadeTimeBase) + // bit 4..7 - 0 = Disabled (E_DALIExtendeFadeTimeMultiplier) + // 1 = Multiplier100ms + // 2 = Multiplier1s + // 3 = Multiplier10s + // 4 = Multiplier1min +#define DALI_102_RESERVED49 0x0031 // 49 - [Reserved] + // ... +#define DALI_102_RESERVED63 0x003F // 63 - [Reserved] +#define DALI_102_SET_SCENE0 0x0040 // 64 - Specifies the DTR data as Scene XXXX. + // The value 255 ("MASK") removes the ballast from the scene. + // ... +#define DALI_102_SET_SCENE15 0x004F // 79 - Specifies the DTR data as Scene XXXX. +#define DALI_102_REMOVE_FROM_SCENE0 0x0050 // 80 - Deletes the Scene XXXX setting. + // This stores 255 ("MASK") in the specified scene register. + // ... +#define DALI_102_REMOVE_FROM_SCENE15 0x005F // 95 - Deletes the Scene XXXX setting. +#define DALI_102_ADD_TO_GROUP0 0x0060 // 96 - Adds the ballast to Group XXXX. + // ... +#define DALI_102_ADD_TO_GROUP15 0x006F // 111 - Adds the ballast to Group XXXX. +#define DALI_102_REMOVE_FROM_GROUP0 0x0070 // 112 - Deletes the ballast from Group XXXX. + // ... +#define DALI_102_REMOVE_FROM_GROUP15 0x007F // 127 - Deletes the ballast from Group XXXX. +#define DALI_102_SET_SHORT_ADDRESS 0x0080 // 128 - Specifies the DTR data as a Short Address. + // The DTR must contain either: + // - (address<<1)|1 (i.e. 0AAAAAA1) to set a short address + // - 255 (i.e. 11111111) to remove the short address +#define DALI_102_ENABLE_WRITE_MEMORY 0x0081 // 129 - Allows writing of the memory bank. + // writeEnableState shall be set to ENABLED. + // NB there is no command to explicitly disable memory write access; any command that is not directly involved with writing to + // memory banks will set writeEnableState to DISABLED. + // The commands that do not set writeEnableState to DISABLED are: + // - WriteMemoryLocation + // - WriteMemoryLocationNoReply + // - DTR0 + // - DTR1 + // - DTR2 + // - QueryContentDTR0 + // - QueryContentDTR1 + // - QueryContentDTR2 +#define DALI_102_RESERVED130 0x0082 // 130 - [Reserved] + // ... +#define DALI_102_RESERVED143 0x008F // 143 - [Reserved] + +// Query commands - Send as second byte +#define DALI_102_QUERY_STATUS 0x0090 // 144 - Returns "STATUS INFORMATION" + // bit 0 - Status of the control gear. 0: OK. + // bit 1 - Lamp failure. 0: OK. + // bit 2 - Lamp power on. 0: OFF. + // bit 3 - Limit value error. 0: the most recently requested lamp power was either between MIN LEVEL and MAX LEVEL or was OFF. + // bit 4 - Fading completed: 0: fading finished. 1: fading active. + // bit 5 - Reset status. 0: no. + // bit 6 - Short address missing. 0: no. + // bit 7 - Power supply fault. 0: No. A reset or a lamp power control command has been received since the last switch-on. +#define DALI_102_QUERY_CONTROL_GEAR_PRESENT 0x0091 // 145 - Returns bit0 - Is there a ballast that can communicate? +#define DALI_102_QUERY_LAMP_FAILURE 0x0092 // 146 - Returns bit1 - Is there a lamp problem? +#define DALI_102_QUERY_LAMP_POWER_ON 0x0093 // 147 - Returns bit2 - Is a lamp on? +#define DALI_102_QUERY_LIMIT_ERROR 0x0094 // 148 - Returns bit3 - Is the specified lighting control level out of the range from the minimum to the maximum values? +#define DALI_102_QUERY_RESET_STATE 0x0095 // 149 - Returns bit5 - Is the ballast in 'RESET STATE'? +#define DALI_102_QUERY_MISSING_SHORT_ADDRESS 0x0096 // 150 - Returns bit6 - Does the ballast not have a short address? +#define DALI_102_QUERY_VERSION_NUMBER 0x0097 // 151 - What is the corresponding IEC standard number? + // The high four bits of the answer represent the version number of the standard. + // IEC-60929 is version number 0; the 2009 version of IEC-62386 is version number 1. + // As of the 2014 version of IEC-62386, the answer shall be the content of memory bank 0 location 0x16. + // bit 0..3 - nMinorVersion + // bit 4..7 - nMajorVersion +#define DALI_102_QUERY_CONTENT_DTR0 0x0098 // 152 - What is the DTR content? +#define DALI_102_QUERY_DEVICE_TYPE 0x0099 // 153 - What is the device type? + // The device type affects which application extended commands the device will respond to. + // XXX this is updated for IEC 62386-102 and interacts with QueryNextDeviceType. In this case: + // - If the device does not implement any part 2xx device type then the response will be 254; + // - If the device implements one part 2xx device type then the response will be the device type number; + // - If the device implements multiple part 2xx device types then the response will be MASK (0xff). + // value 0 - Part 201: Standard device + // value 1 - Part 202: Device for emergency lighting. + // value 2 - Part 203: Device for discharge lamps. + // value 3 - Part 204: Device for low-voltage halogen lamps. + // value 4 - Part 205: Device for dimming incandescent lamps. + // value 5 - Part 206: Device for converting digital signals into DC signals. + // value 6 - Part 207: Device for light emitting diodes (LEDs). + // value 7 - Part 208: Device for switching functions. + // value 8 - Part 209: Device for color/color temperature control. + // value 9 - Part 210: Sequencer + // value 15 - Part 216: Load referencing + // value 16 - Part 217: Thermal gear protection + // value 17 - Part 218: Dimming curve selection + // value 19 - Part 220: Centrally supplied emergency operation + // value 20 - Part 221: Load shedding + // value 21 - Part 222: Thermal lamp protection + // value 23 - Part 224: Non-replaceable light sources + // value 49 - Part 250: Devices with integrated DALI bus power supply + // value 50 - Part 251: Further information and parameters for DALI control gears in memory bank 1 + // value 51 - Part 252: Further parameters for the creation of an energy report + // value 52 - Part 253: Further parameters with diagnostic and maintenance information for DALI control gears + // value 53 - Part 254: Extended information for DALI control gears for emergency lighting + // value 254 - None or end + // value 255 - Multiple +#define DALI_102_QUERY_PHYSICAL_MINIMUM_LEVEL 0x009A // 154 - Return the physical minimum level for this device. +#define DALI_102_QUERY_POWER_FAILURE 0x009B // 155 - Ask whether the device has not received a "RESET" or arc power control command since the last power-on. +#define DALI_102_QUERY_CONTENT_DTR1 0x009C // 156 - Return the contents of DTR1. +#define DALI_102_QUERY_CONTENT_DTR2 0x009D // 157 - Return the contents of DTR2. +#define DALI_102_QUERY_OPERATING_MODE 0x009E // 158 - DALI-2 What is the Operating Mode? +#define DALI_102_QUERY_LIGHT_SOURCE_TYPE 0x009F // 159 - DALI-2 What is the Light source type (E_DALILightSourceType) + // "unknown" will typically be used in case of signal conversion, for example to 1-10v dimming + // "none" will be used where no light source is connected, for example a relay + // When the response is "multiple" then the light source types shall be placed into DTR0, DTR1 and DTR2. + // If there are exactly two light source types, DTR2 shall be "none". If there are more than three then DTR2 shall be MASK. + // value 0 = LowPressureFluorescent + // value 2 = HID + // value 3 = LowVoltageHalogen + // value 4 = Incandescent + // value 6 = LED + // value 7 = OLED + // value 252 = Other + // value 253 = Unknown (typicaly signal conversion like 1-10V dimming) + // value 254 = NoLightSource + // value 255 = Multiple (Type in DTR0, DTR1 and DTR2 (= none if two types, = 255 if > 3)) +#define DALI_102_QUERY_ACTUAL_LEVEL 0x00A0 // 160 - What is the "ACTUAL LEVEL" (the current lighting control level)? + // During preheating and if a lamp error occurs the answer will be 0xff ("MASK"). +#define DALI_102_QUERY_MAX_LEVEL 0x00A1 // 161 - What is the maximum lighting "MAX LEVEL" control level? +#define DALI_102_QUERY_MIN_LEVEL 0x00A2 // 162 - What is the minimum lighting "MIN LEVEL" control level? +#define DALI_102_QUERY_POWER_ON_LEVEL 0x00A3 // 163 - What is the "POWER ON LEVEL" (the lighting control level when the power is turned on)? +#define DALI_102_QUERY_SYSTEM_FAILURE_LEVEL 0x00A4 // 164 - What is the "SYSTEM FAILURE LEVEL" (the lighting control level when a failure occurs)? +#define DALI_102_QUERY_FADE_TIME_FADE_RATE 0x00A5 // 165 - What are the Fade time and Fade rate? (see 47 and 48) + // The fade time set by "DALI_102_SET_FADE_TIME" is in the upper four bits of the response. + // The fade rate set by "DALI_102_SET_FADE_RATE" is in the lower four bits of the response. +#define DALI_102_QUERY_MANUFACTURER_SPECIFIC_MODE 0x00A6 // 166 - DALI-2 Query Manufacturer Specific Mode + // The answer shall be YES when operatingMode is in the range 0x80..0xff and NO otherwise. +#define DALI_102_QUERY_NEXT_DEVICE_TYPE 0x00A7 // 167 - DALI-2 What is the next Device Type? + // If directly preceded by DALI_102_QUERY_DEVICE_TYPE and more than one device type is supported, returns the first and lowest device type number. + // If directly preceded by DALI_102_QUERY_NEXT_DEVICE_TYPE and not all device types have been reported, returns the next lowest device type number. + // If directly preceded by DALI_102_QUERY_NEXT_DEVICE_TYPE and all device types have been reported, returns 254. + // In all other cases returns NO (no response). + // Multi-master transmitters shall send the sequence DALI_102_QUERY_DEVICE_TYPE,DALI_102_QUERY_NEXT_DEVICE_TYPE,... as a transaction. +#define DALI_102_QUERY_EXTENDED_FADE_TIME 0x00A8 // 168 - DALI-2 What is the Extended Fade Time? + // bit 0..3 - value 0..15 (E_DALIExtendedFadeTimeBase) + // bit 4..7 - 0 = Disabled (E_DALIExtendeFadeTimeMultiplier) + // 1 = Multiplier100ms + // 2 = Multiplier1s + // 3 = Multiplier10s + // 4 = Multiplier1min +#define DALI_102_QUERY_CONTROL_GEAR_FAILURE 0x00A9 // 169 - DALI-2 Does a ballast have the abnormality (0 = No, 1 = Yes)? + // The answer shall be YES if controlGearFailure is TRUE and NO otherwise. +#define DALI_102_RESERVED170 0x00AA // 170 - [Reserved] + // ... +#define DALI_102_RESERVED175 0x00AF // 175 - [Reserved] +#define DALI_102_QUERY_SCENE0_LEVEL 0x00B0 // 176 - Return the level set for scene 0, or 255 ("MASK") if the device is not part of the scene. + // ... +#define DALI_102_QUERY_SCENE15_LEVEL 0x00BF // 191 - Return the level set for scene 15, or 255 ("MASK") if the device is not part of the scene. +#define DALI_102_QUERY_GROUPS_0_7 0x00C0 // 192 - Return the device membership of groups 0-7 with group 0 in the least-significant bit of the response. +#define DALI_102_QUERY_GROUPS_8_15 0x00C1 // 193 - Return the device membership of groups 8-15 with group 8 in the least-significant bit of the response. +#define DALI_102_QUERY_RANDOM_ADDRESS_H 0x00C2 // 194 - What are the high 8 bits of the random address? +#define DALI_102_QUERY_RANDOM_ADDRESS_M 0x00C3 // 195 - What are the middle 8 bits of the random address? +#define DALI_102_QUERY_RANDOM_ADDRESS_L 0x00C4 // 196 - What are the low 8 bits of the random address? +#define DALI_102_READ_MEMORY_LOCATION 0x00C5 // 197 - What is the memory location content (Uses DTR0 and DTR1) + // The query is ignored if the addressed memory bank is not implemented. + // If executed, the answer will be the content of the memory location identified by DTR0 in bank DTR1. + // If the addressed location is below 0xff, then DTR0 is incremented by 1. +#define DALI_102_RESERVED198 0x00C6 // 198 - [Reserved] + // ... +#define DALI_102_RESERVED223 0x00DF // 223 - [Reserved] + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 201 = DT0 - Send as second byte + * Standard device like fluorescent lamps +\*-------------------------------------------------------------------------------------------*/ + +// Application extended query commands - Send as second byte +#define DALI_201_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 202 = DT1 - Send as second byte + * Device for emergency lighting +\*-------------------------------------------------------------------------------------------*/ + +// Application extended query commands - Send as second byte +#define DALI_202_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 203 = DT2 - Send as second byte + * Device for discharge lamps excluding fluorescent lamps +\*-------------------------------------------------------------------------------------------*/ + +// Application extended query commands - Send as second byte +#define DALI_203_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 204 = DT3 - Send as second byte + * Device for low-voltage halogen lamps +\*-------------------------------------------------------------------------------------------*/ + +// Application extended query commands - Send as second byte +#define DALI_204_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 205 = DT4 - Send as second byte + * Device for dimming incandescent lamps +\*-------------------------------------------------------------------------------------------*/ + +// Application extended configuration commands - Send as second byte with repeat +#define DALI_205_SET_REFERENCE_SYSTEM_POWER 0x00E0 // 224 - Reference System Power + // The control gear shall measure and store system power levels in order to detect load increase or load decrease. + // The measurement may take up to 15 minutes. + // Measured power levels will be stored in non-volatile memory, Commands received during the measuring period will be ignored except query commands and Terminate. + // The process will be aborted if DALI_102_TERMINATE is received. +#define DALI_205_SELECT_DIMMING_CURVE 0x00E1 // 225 - Select Dimming Curve + // If DTR0 is 0 then selects the standard logarithmic curve + // If DTR0 is 1 then selects a linear dimming curve + // Other values of DTR0 are reserved and will not change the dimming curve. + // The setting is stored in non-volatile memory and is not cleared by the Reset command. +#define DALI_205_RESERVED226 0x00E2 // 226 - [Reserved] + // ... +#define DALI_205_RESERVED237 0x00ED // 237 - [Reserved] + +// Application extended query commands - Send as second byte +#define DALI_205_QUERY_DIMMING_CURVE 0x00EE // 238 - Returns Dimming curve in use + // value 0 = Standard - Standard logarithmic dimming curve + // value 1 = Linear - Linear dimming curve + // value 255 = Unknown +#define DALI_205_QUERY_DIMMER_STATUS 0x00EF // 239 - Returns dimmer status + // bit 0 - leading edge mode running + // bit 1 - trailing edge mode running + // bit 2 - reference measurement running + // bit 3 - None + // bit 4 - non-logarithmic dimming curve active + // bit 5..7 - Not used +#define DALI_205_QUERY_FEATURES 0x00F0 // 240 - Return feature bytes. There are three bytes of feature information. + // Byte 1 is the reply to this command. + // bit 0 - load over-current shutdown can be queried + // bit 1 - open circuit detection can be queried + // bit 2 - detection of load decrease can be queried + // bit 3 - detection of load increase can be queried + // bit 4 - None + // bit 5 - thermal shutdown can be queried + // bit 6 - thermal overload with output level reduction can be queried + // bit 7 - physical selection supported + // Byte 2 is transferred to DTR0. + // bit 0 - temperature can be queried + // bit 1 - supply voltage can be queried + // bit 2 - supply frequency can be queried + // bit 3 - load voltage can be queried + // bit 4 - load current can be queried + // bit 5 - real load power can be queried + // bit 6 - load rating can be queried + // bit 7 - load current overload with output level reduction can be queried + // Byte 3 is transferred to DTR1. + // bit 0..1 - Dimming method + // value 0 = leading & trailing + // value 1 = leading only + // value 2 = trailing only + // value 3 = sine wave + // bit 2 - None + // bit 3 - non-logarithmic dimming curve can be selected + // bit 4..6 - None + // bit 7 - load unsuitable can be queried +#define DALI_205_QUERY_FAILURE_STATUS 0x00F1 // 241 - Returns failure status. There are two bytes of failure information. + // Responds with byte 1 of the failure status information, and transfers byte 2 of the failure status into DTR1. + // Failure states which cause output level reduction shall only be reset by re-powering the control gear or by any command that causes the output to turn off. + // Failure states which cause shutdown shall only be reset by re-powering the control gear or using an optional reset switch on the control gear. + // Byte 1 is the reply to this command. + // bit 0 - load over-current shutdown + // bit 1 - open circuit detected + // bit 2 - load decrease detected + // bit 3 - load increase detected + // bit 4 - None + // bit 5 - thermal shutdown + // bit 6 - thermal overload with output level reduction + // bit 7 - reference measurement failed + // Byte 2 is transferred to DTR1. + // bit 0 - load not suitable for selected dimming method + // bit 1 - supply voltage out of limits + // bit 2 - supply frequency out of limits + // bit 3 - load voltage out of limits + // bit 4 - load current overload with output level reduction + // bit 5..7 - Not used +#define DALI_205_QUERY_DIMMER_TEMPERATURE 0x00F2 // 242 - Returns the temperature of the dimmer with 1 degC resolution. + // Values of 0 to 254 represent temperatures of -40C to +214C. + // Below -40C, 0 is returned. Above 214C, 254 is returned. A value of 255 means "unknown". + // Control gear without this feature shall not react. +#define DALI_205_QUERY_RMS_SUPPLY_VOLTAGE 0x00F3 // 243 - Returns the measured supply voltage. + // Values of 0 to 254 represent 0V to 508V RMS. + // Voltages above 508V RMS shall be returned as 254. A value of 255 means "unknown". + // Control gear without this feature shall not react. +#define DALI_205_QUERY_SUPPLY_FREQUENCY 0x00F4 // 244 - Returns the supply frequency with 0.5Hz resolution. + // Values of 0 to 254 represent 0Hz to 127Hz. + // Frequencies above 127Hz are returned as 254. A value of 255 means "unknown". + // Control gear without this feature shall not react. +#define DALI_205_QUERY_RMS_LOAD_VOLTAGE 0x00F5 // 245 - Returns the measured load voltage. + // Values of 0 to 254 represent 0V to 508V RMS. + // Voltages above 508V RMS shall be returned as 254. A value of 255 means "unknown". + // Control gear without this feature shall not react. +#define DALI_205_QUERY_RMS_LOAD_CURRENT 0x00F6 // 246 - Returns the measured load current as a percentage of the rated load current given by the answer to QueryLoadRating, with 0.5% resolution. + // Values of 0 to 254 represent 0% to 127%. + // Higher currents shall be returned as 254. A value of 255 means "unknown". + // Control gear without this feature shall not react. +#define DALI_205_QUERY_REAL_LOAD_POWER 0x00F7 // 247 - Returns the high byte of the real power supplied to the load. The low byte is transferred to DTR0. + // Values of 0 to 65534 represent powers from 0W to 16383.5W with a resolution of 0.25W. + // Powers above this range are returned as 65534. A value of 65535 means "unknown". + // Control gear without this feature shall not react. +#define DALI_205_QUERY_LOAD_RATING 0x00F8 // 248 - Returns the maximum load current rating with 150mA resolution. + // Values of 0 to 254 represent 0A to 38.1A RMS. + // Currents above 38.1A shall be returned as 254. A value of 255 means "unknown". + // Control gear without this feature shall not react. +#define DALI_205_QUERY_REFERENCE_RUNNING 0x00F9 // 249 - Asks if the ReferenceSystemPower measurement is running. +#define DALI_205_QUERY_REFERENCE_FAILED 0x00FA // 250 - Asks if the reference measurement started by ReferenceSystemPower failed. +#define DALI_205_RESERVED251 0x00FB // 251 - [Reserved] + // ... +#define DALI_205_RESERVED254 0x00FE // 254 - [Reserved] +#define DALI_205_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 206 = DT5 - Send as second byte + * Device for converting digital signales into DC signals +\*-------------------------------------------------------------------------------------------*/ + +// Application extended query commands - Send as second byte +#define DALI_206_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 207 = DT6 - Send as second byte + * Device for Light Emitting Diodes (LEDs) + * Variables + * Name Reset value Scope Size Comment + * --------------- --------------------------- ------------------------------------------- ------ --------- + * minFastFadeTime No change E_DALIFastFadeTime.T100ms 1 byte Read only + * ... + * E_DALIFastFadeTime.T700ms + * fastFadeTime E_DALIFastFadeTime.Disabled E_DALIFastFadeTime.Disabled,minFastFadeTime 1 byte + * ... + * E_DALIFastFadeTime.T700ms + * controlGearType No change 0...255 1 byte Read only + * features No change 0...255 1 byte Read only + * failureStatus No change 0...255 1 byte Read only + * dimmingCurve E_DALIDimmingCurve.Standard E_DALIDimmingCurve.Standard, 1 byte + * E_DALIDimmingCurve.Linear +\*-------------------------------------------------------------------------------------------*/ + +// Application extended configuration commands - Send as second byte with repeat +#define DALI_207_REFERENCE_SYSTEM_POWER 0x00E0 // 224 - The DALI control gear measures and stores the performance level of the system, in order to detect load increase and decrease. +#define DALI_207_ENABLE_CURRENT_PROTECTOR 0x00E1 // 225 - Enables the current protection. +#define DALI_207_DISABLE_CURRENT_PROTECTOR 0x00E2 // 226 - Disables the current protection. +#define DALI_207_SELECT_DIMMING_CURVE 0x00E3 // 227 - Selects Dimming curve (see 238). + // If DTR0 is 0 then selects the standard logarithmic curve + // If DTR0 is 1 then selects a linear dimming curve + // Other values of DTR0 are reserved and will not change the dimming curve. + // The setting is stored in non-volatile memory and is not cleared by the Reset command. +#define DALI_207_SET_FAST_FADE_TIME 0x00E4 // 228 - Sets the DTR0 of the data as Fast Fade Time (see 253). +#define DALI_207_RESERVED229 0x00E5 // 229 - [Reserved] + // ... +#define DALI_207_RESERVED236 0x00EC // 236 - [Reserved] + +// Application extended query commands - Send as second byte +#define DALI_207_QUERY_GEAR_TYPE 0x00ED // 237 - Returns ‘GEAR TYPE’ + // bit 0 - LED power supply integrated + // bit 1 - LED module integrated + // bit 2 - AC supply possible + // bit 3 - DC supply possible + // bit 4..7 - Reserve +#define DALI_207_QUERY_DIMMING_CURVE 0x00EE // 238 - Returns Dimming curve in use (E_DALIDimmingCurve) + // value 0 = Standard - Standard logarithmic dimming curve + // value 1 = Linear - Linear dimming curve + // value 255 = Unknown +#define DALI_207_QUERY_POSSIBLE_OPERATING_MODE 0x00EF // 239 - Returns ‘POSSIBLE OPERATING MODE’ + // bit 0 - PWM mode possible + // bit 1 - AM mode possible + // bit 2 - Output is current controlled + // bit 3 - High current pulse mode + // bit 4..7 - Reserve +#define DALI_207_QUERY_FEATURES 0x00F0 // 240 - Returns ‘FEATURES’ + // bit 0 - Short circuit detection can be queried + // bit 1 - Open circuit detection can be queried + // bit 2 - Detection of the load decrease can be queried + // bit 3 - Detection of the load increase can be queried + // bit 4 - Current protector is implemented and can be queried + // bit 5 - Thermal shutdown can be queried + // bit 6 - Reduction of the output level due to thermal overload can be queried + // bit 7 - Physical selection supported +#define DALI_207_QUERY_FAILURE_STATUS 0x00F1 // 241 - Returns ‘FAILURE STATUS’ + // bit 0 - Short circuit + // bit 1 - Open circuit + // bit 2 - Load decrease + // bit 3 - Load increase + // bit 4 - Current protector active + // bit 5 - Thermal shutdown + // bit 6 - Thermal overload with output level reduction + // bit 7 - Reference measurement failed +#define DALI_207_QUERY_SHORT_CIRCUIT 0x00F2 // 242 - Returns bit0 short circuit of ‘FAILURE STATUS’ +#define DALI_207_QUERY_OPEN_CIRCUIT 0x00F3 // 243 - Returns bit1 open circuit of ‘FAILURE STATUS’ +#define DALI_207_QUERY_LOAD_DECREASE 0x00F4 // 244 - Returns bit2 load decrease of ‘FAILURE STATUS’ +#define DALI_207_QUERY_LOAD_INDREASE 0x00F5 // 245 - Returns bit3 load increase of‘FAILURE STATUS’ +#define DALI_207_QUERY_CURRENT_PROTECTOR_ACTIVE 0x00F6 // 246 - Returns bit4 current protector active of ‘FAILURE STATUS’ +#define DALI_207_QUERY_THERMAL_SHUTDOWN 0x00F7 // 247 - Returns bit5 thermal shut down of ‘FAILURE STATUS’ +#define DALI_207_QUERY_THERMAL_OVERLOAD 0x00F8 // 248 - Returns bit6 thermal overload with light level reduction of ‘FAILURE STATUS’ +#define DALI_207_QUERY_REFERENCE_RUNNING 0x00F9 // 249 - Returns whether Reference System Power is in operation. +#define DALI_207_QUERY_REFERENCE_MEASURMENT_FAILED 0x00FA // 250 - Returns bit7 reference measurement failed of ‘FAILURE STATUS’ +#define DALI_207_QUERY_CURRENT_PROTECTOR_ENABLE 0x00FB // 251 - Returns state of Curent protector +#define DALI_207_QUERY_OPERATING_MODE2 0x00FC // 252 - Returns ‘OPERATING MODE’ + // bit 0 - PWM mode active + // bit 1 - AM mode active + // bit 2 - Output is current controlled + // bit 3 - High current pulse mode is active + // bit 4 - non-logarithmic dimming curve active + // bit 5..7 - Reserve +#define DALI_207_QUERY_FAST_FADE_TIME 0x00FD // 253 - Returns set Fast fade time (E_DALIFastFadeTime) + // value 0 = Disabled + // value 4 = T100ms + // value 8 = T200ms + // value 9 = T225ms + // value 12 = T300ms + // value 16 = T400ms + // value 20 = T500ms + // value 24 = T600ms + // value 27 = T700ms + // value 255 = Unknown +#define DALI_207_QUERY_MIN_FAST_FADE_TIME 0x00FE // 254 - Returns set Minimum fast fade time (variable minFastFadeTime) +#define DALI_207_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 208 = DT7 - Send as second byte + * Device for switching functions +\*-------------------------------------------------------------------------------------------*/ + +// Application extended query commands - Send as second byte +#define DALI_208_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 209 = DT8 - Send as second byte + * Device for controlling colour and colour temperature + * Tc is expressed in MIREK and can vary from 1 Mirek (1000000 Kelvin) to 65534 Mirek (15.26 Kelvin) + * RGBWAF - Red, Green, Blue, White, Amber, Freely selectable color +\*-------------------------------------------------------------------------------------------*/ + +// Application extended control commands - Send as second byte with repeat +#define DALI_209_SET_TEMPORARY_X_COORDINATE 0x00E0 // 224 - Set temporary x-COORDINATE (Uses DTR0 (LSB) and DTR1 (MSB)) + // The value is expressed in units of 1/65536. The maximum x-COORDINATE value is 0,99997 +#define DALI_209_SET_TEMPORARY_Y_COORDINATE 0x00E1 // 225 - Set temporary y-COORDINATE (Uses DTR0 (LSB) and DTR1 (MSB)) + // The value is expressed in units of 1/65536. The maximum y-COORDINATE value is 0,99997. +#define DALI_209_ACTIVATE 0x00E2 // 226 - Transfer buffered values of temporary registers to the lamp. + // It ends a running cross-fade and starts a new cross-fade for the respective color/color temperature. +#define DALI_209_X_COORDINATE_STEP_UP 0x00E3 // 227 - The x-COORDINATE shall be set 256 steps higher (256/65536) immediately without fading. + // This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set. + // If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by + // the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’. +#define DALI_209_X_COORDINATE_STEP_DOWN 0x00E4 // 228 - The x-COORDINATE shall be set 256 steps lower (256/65536) immediately without fading. + // This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set. + // If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by + // the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’. +#define DALI_209_Y_COORDINATE_STEP_UP 0x00E5 // 229 - The y-COORDINATE shall be set 256 steps higher (256/65536) immediately without fading. + // This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set. + // If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by + // the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’. +#define DALI_209_Y_COORDINATE_STEP_DOWN 0x00E6 // 230 - The y-COORDINATE shall be set 256 steps lower (256/65536) immediately without fading. + // This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set. + // If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by + // the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’. +#define DALI_209_SET_TEMPORARY_COLOUR_TEMP_TC 0x00E7 // 231 - Set temporary colour temperature Tc (Uses DTR0 (LSB) and DTR1 (MSB)) + // The value is expressed in units of 1 Mirek. + // A value of 0 for Tc shall be ignored and therefore not stored in memory. + // NOTE Colour temperature TC can vary from 1 Mirek (1 000 000 K) to 65 534 Mirek (15,26 K). +#define DALI_209_COLOUR_TEMP_TC_STEP_COOLER 0x00E8 // 232 - The ‘COLOUR TEMPERATURE TC’ shall be set 1 Mirek lower immediately without fading. + // This command shall only be executed when ‘Colour type colour temperature TC active’ bit, bit 5 of the ‘COLOUR STATUS’ is set. + // No change shall occur if ‘COLOUR TEMPERATURE TC’ is already at ‘COLOUR TEMPERATURE TC COOLEST’. + // If the new colour value does not correspond to a colour temperature attainable by the control gear, this shall be indicated by + // the ‘Colour temperature TC out of range’ bit, bit 1 of the ‘COLOUR STATUS’. +#define DALI_209_COLOUR_TEMP_TC_STEP_WARMER 0x00E9 // 233 - The ‘COLOUR TEMPERATURE TC’ shall be set 1 Mirek higher immediately without fading. + // This command shall only be executed when ‘Colour type colour temperature TC active’ bit, bit 5 of the ‘COLOUR STATUS’ is set. + // No change shall occur if ‘COLOUR TEMPERATURE TC’ is already at ‘COLOUR TEMPERATURE TC WARMEST’. + // If the new colour value does not correspond to a colour temperature attainable by the control gear, this shall be indicated by + // the ‘Colour temperature TC out of range’ bit, bit 1 of the ‘COLOUR STATUS’. +#define DALI_209_SET_TEMPORARY_PRIMARY_N_DIMLEVEL 0x00EA // 234 - Set temporary primary N dimlevel (Uses DTR0 (LSB), DTR1 (MSB) and DTR2 (N)) + // The value is expressed in units of 1/65536. + // The maximum ‘PRIMARY N DIMLEVEL’ value is 0,99997 and shall be interpreted on a linear scale. + // N depends on DTR2 and shall be in the range from 0 to 5 depending upon the available number of primaries. + // For any other value of DTR2 the command shall be ignored. +#define DALI_209_SET_TEMPORARY_RGB_DIMLEVEL 0x00EB // 235 - Set temporary RGB dimlevel + // The data in the DTR shall be set as ‘TEMPORARY RED DIMLEVEL’. + // The data in DTR1 shall be set as ‘TEMPORARY GREEN DIMLEVEL’. + // The data in DTR2 shall be set as ‘TEMPORARY BLUE DIMLEVEL’. +#define DALI_209_SET_TEMPORARY_WAF_DIMLEVEL 0x00EC // 236 - Set temporary WAF dimlevel + // The data in the DTR shall be set as ‘TEMPORARY WHITE DIMLEVEL’. + // The data in DTR1 shall be set as ‘TEMPORARY AMBER DIMLEVEL’. + // The data in DTR2 shall be set as ‘TEMPORARY FREECOLOUR DIMLEVEL’. +#define DALI_209_SET_TEMPORARY_RGBWAF_CONTROL 0x00ED // 237 - Set temporary RGBWAF control via DTR0 + // The data in the DTR shall be stored as ‘TEMPORARY RGBWAF CONTROL’. + // bit 0 - output channel 0/Red; '0' = Unlinked, '1' = Linked + // bit 1 - output channel 1/Green; '0' = Unlinked, '1' = Linked + // bit 2 - output channel 2/Blue; '0' = Unlinked, '1' = Linked + // bit 3 - output channel 3/White; '0' = Unlinked, '1' = Linked + // bit 4 - output channel 4/Amber; '0' = Unlinked, '1' = Linked + // bit 5 - output channel 5/Freecolour; '0' = Unlinked, '1' = Linked + // bits 6..7 control type + // value 0 = Channel control + // value 1 = Colour control + // value 2 = Normalised colour control + // value 3 = reserved + // Bit 0 to bit 5 sets the appropriate output channel(s)/colour(s) linked or unlinked. + // Bit 6 and bit 7: The control type defines how the gear shall react to Arc Power Commands. + // The linked channels shall all be set to unlinked on any colour activation with colour type xy-coordinate, colour temperature TC or primary N. + // NOTE More than one channel can be linked at the same time +#define DALI_209_COPY_REPORT_TO_TEMPORARY 0x00EE // 238 - Copy the contents of the variables with the color settings to the variables for the temporary color settings. + +// Application extended configuration commands - Send as second byte with repeat +#define DALI_209_RESERVED239 0x00EF // 239 - [Reserved] +#define DALI_209_STORE_TY_PRIMARY_N 0x00F0 // 240 - Store TY Primary N via DTR0/1/2 + // The value is expressed in units of 0,5 lumen resulting in a possible range of TYmin = 0 lumen, to TYmax = 32767 lumen. + // A value of 65535 (“MASK”) means unknown. + // N depends on DTR2 and shall be in the range from 0 to 5 depending upon the available number of primaries. + // For any other value of DTR2 the command shall be ignored. + // A value of “MASK” means that this primary is undefined and calibration is needed. +#define DALI_209_STORE_XY_COORDINATE_PRIMARY_N 0x00F1 // 241 - Store XY coord primary channel N via DTR2 + // The ‘TEMPORARY x-COORDINATE’ and the ‘TEMPORARY y-COORDINATE’, given by command 224 and command 225 shall be stored as ‘x-COORDINATE PRIMARY N’ + // respectively ‘y-COORDINATE PRIMARY N’ of primary N given by the value of DTR2, and shall be in the range from 0 to 5 depending upon the available number of primaries. + // For any other value of DTR2 the command shall be ignored. + // A value of “MASK” in one of the “temporary colour value” values shall be stored which means that this primary is undefined and calibration is needed. + // NOTE 1 The intended use of this command is to store the actual xy-coordinate belonging to the primary. Any other use can lead to unexpected results (colours). + // NOTE 2 xy-coordinates outside the CIE 1931 colour space chromaticity diagram are not meaningful. +#define DALI_209_STORE_COLOUR_TEMP_TC_LIMIT 0x00F2 // 242 - Set color temperature Tc limit in Mirek (Uses DTR0 (LSB), DTR1 (MSB) and DTR2 (TcLimit type)) + // The value shall be stored in a variable defined by DTR2. + // For any other value of DTR2 the command shall be ignored. + // DTR2 = 0 - ColorTemperatureTcCoolest (lowest possible value but always equal to or warmer than the lowest possible physical value) + // DTR2 = 1 - ColorTemperatureTcWarmest (highest possible value but always equal to or cooler than the highest possible physical value) + // DTR2 = 2 - ColorTemperatureTcPhysicalCoolest (lowest possible physical value) + // DTR2 = 3 - ColorTemperatureTcPhysicalWarmest (highest possible physical value) +#define DALI_209_STORE_GEAR_FEATURES_STATUS 0x00F3 // 243 - Set gear features / status (See 247) (Uses DTR0) + // The data in the DTR shall be interpreted as follows: + // bit 0 - Automatic Activation; '0' = No + // bit 1..7 - reserved; ‘0’ = No + // If bit 0, the ‘Automatic Activation’ bit, is set to 1, all arc power control commands except “ENABLE DAPC SEQUENCE” shall automatically trigger a colour transition. + // If the ‘Automatic Activation’ bit is set, bit 0 of the “GEAR FEATURES/STATUS” byte shall be set. +#define DALI_209_RESERVED244 0x00F4 // 244 - [Reserved] +#define DALI_209_ASSIGN_COLOUR_TO_LINKED_COMMAND 0x00F5 // 245 - Assign to linked channel via DTR0 + // The data held in the DTR in the range 0 to 6 shall be used to assign any/all linked output channel(s) to the given colour. + // DTR0 = 0 - No colour assigned + // DTR0 = 1 - Red + // DTR0 = 2 - Green + // DTR0 = 3 - Blue + // DTR0 = 4 - White + // DTR0 = 5 - Amber + // DTR0 = 6 - Freecolour + // For any other value of the DTR the command shall be ignored. + // The linked channels are given by bit 0 to bit 5 held in “TEMPORARY RGBWAF CONTROL”. + // If “TEMPORARY RGBWAF CONTROL” holds “MASK” the channel assignment shall not be changed. + // The “TEMPORARY COLOUR SETTINGS” are set to “MASK” after use of this command. +#define DALI_209_START_AUTO_CALIBRATION 0x00F6 // 246 - Start auto calibration + // The command shall start or re-trigger a 15 min timer. Bit 2 of “COLOUR STATUS” shall be set to “1” whilst this timer is running. + // When the timer stops the most recent colour type, colour value and arc power level shall be restored immediately + // Whilst the timer is running the control gear shall run a calibration procedure in order to measure the x-coordinate, y-coordinate and the TY-value of + // all supported primaries and bit 3 of “COLOUR STATUS” shall be set to “0”. + // While the calibration procedure is running, the control gear shall not react to any command except “TERMINATE”, “QUERY COLOUR STATUS” and “START AUTO CALIBRATION”. + // The "TERMINATE" command shall cause the procedure to be aborted and the timer to be stopped. + // If the calibration is successful then bit 3 of “COLOUR STATUS” shall be set to “1” and the timer shall be stopped. + // If the calibration is not successful (bit 3 of “COLOUR STATUS” is “0”) and the control gear is capable of recovering the + // last successful calibration data it shall do so. + // In this case bit 3 of “COLOUR STATUS” shall bet set to “1”. + // The capability to recover the last successful calibration data is a gear feature; see command 247. + // Auto calibration is a gear feature; see command 247. If this feature is not supported the control gear shall not react in any way. + // NOTE Due to the fact that the calibration process may take longer than 15 min, the control device should check the status of the auto calibration by + // command 248 ‘QUERY COLOUR STATUS’ periodically and re-trigger the calibration process timer by command 246 (START AUTO CALIBRATION) if necessary + +// Application extended query commands - Send as second byte +#define DALI_209_QUERY_GEAR_FEATURES_STATUS 0x00F7 // 247 - Returns gear features / status + // bit 0 - Automatic activation + // bit 1..5 - reserved + // bit 6 - Automatic calibration is supported + // bit 7 - Restoration of the automatic calibration is supported +#define DALI_209_QUERY_COLOUR_STATUS 0x00F8 // 248 - Returns color status + // bit 0 - xy coordinate color point is outside the valid range. + // bit 1 - Color temperature Tc lies outside the valid range + // bit 2 - Automatic calibration is active. + // bit 3 - Automatic calibration was successful. + // bit 4 - Color representation xy-coordinate active. + // bit 5 - Color representation color temperature Tc active. + // bit 6 - Color representation primary N active. + // bit 7 - Color representation RGBWAF active. +#define DALI_209_QUERY_COLOUR_TYPE_FEATURES 0x00F9 // 249 - Returns color type + // bit 0 - Supports color representation through xy coordinates. + // bit 1 - Supports color representation through color temperature Tc. + // bit 2..4 - Number of primary N colors supported. A value of 0 means that this color representation by primary colors is not supported. + // bit 5..7 - Number of RGBWAF channels supported. A value of 0 means that this color representation by RGBWAF is not supported. +#define DALI_209_QUERY_COLOUR_VALUE 0x00FA // 250 - Returns color value (DTR0 = E_DALIColourValue) (MSB in response, Uses DTR0 for LSB). + // The answer depends on the DTR0 Value. + // Most responses involve a 16-bit number, in such cases the reponse is the MSB and LSB is loaded into DTR0. + // Answers corresponding to the DTR values related to an active colour type are only valid if the colour type of the requested colour value is + // active (see command 248) or if the control gear is capable of recalculating the requested colour value from the active colour type into a colour + // value of another colour type. If recalculation is not possible this shall be indicated by a value of “MASK” as answer. + // Querying the number of primaries, the x-coordinate, y-coordinate and TY of primary N shall be independent of the implemented colour type. + // If the control gear does not know the coordinates, or the primary is not there, the answer shall be “MASK”. + // E_DALIColourValue (DTR0): + // 0 - XCoordinate + // 1 - YCoordinate + // 2 - ColourTemperatureTC + // 3 - PrimaryNDimLevel0 + // 4 - PrimaryNDimLevel1 + // 5 - PrimaryNDimLevel2 + // 6 - PrimaryNDimLevel3 + // 7 - PrimaryNDimLevel4 + // 8 - PrimaryNDimLevel5 + // 9 - RedDimLevel + // 10 - GreenDimLevel + // 11 - BlueDimLevel + // 12 - WhiteDimLevel + // 13 - AmberDimLevel + // 14 - FreecolourDimLevel + // 15 - RGBWAFControl + // 64 - XCoordinatePrimaryN0 + // 65 - YCoordinatePrimaryN0 + // 66 - TYPrimaryN0 + // 67 - XCoordinatePrimaryN1 + // 68 - YCoordinatePrimaryN1 + // 69 - TYPrimaryN1 + // 70 - XCoordinatePrimaryN2 + // 71 - YCoordinatePrimaryN2 + // 72 - TYPrimaryN2 + // 73 - XCoordinatePrimaryN3 + // 74 - YCoordinatePrimaryN3 + // 75 - TYPrimaryN3 + // 76 - XCoordinatePrimaryN4 + // 77 - YCoordinatePrimaryN4 + // 78 - TYPrimaryN4 + // 79 - XCoordinatePrimaryN5 + // 80 - YCoordinatePrimaryN5 + // 81 - TYPrimaryN5 + // 82 - NumberOfPrimaries + // 128 - ColourTemperatureTcCoolest + // 129 - ColourTemperatureTcPhysicalCoolest + // 130 - ColourTemperatureTcWarmest + // 131 - ColourTemperatureTcPhysicalWarmest + // 192 - TemporaryXCoordinate + // 193 - TemporaryYCoordinate + // 194 - TemporaryColourTemperature + // 195 - TemporaryPrimaryNDimLevel0 + // 196 - TemporaryPrimaryNDimLevel1 + // 197 - TemporaryPrimaryNDimLevel2 + // 198 - TemporaryPrimaryNDimLevel3 + // 199 - TemporaryPrimaryNDimLevel4 + // 200 - TemporaryPrimaryNDimLevel5 + // 201 - TemporaryRedDimLevel + // 202 - TemporaryGreenDimLevel + // 203 - TemporaryBlueDimLevel + // 204 - TemporaryWhiteDimLevel + // 205 - TemporaryAmberDimLevel + // 206 - TemporaryFreecolourDimLevel + // 207 - TemporaryRgbwafControl + // 208 - TemporaryColourType + // 224 - ReportXCoordinate + // 225 - ReportYCoordinate + // 226 - ReportColourTemperatureTc + // 227 - ReportPrimaryNDimLevel0 + // 228 - ReportPrimaryNDimLevel1 + // 229 - ReportPrimaryNDimLevel2 + // 230 - ReportPrimaryNDimLevel3 + // 231 - ReportPrimaryNDimLevel4 + // 232 - ReportPrimaryNDimLevel5 + // 233 - ReportRedDimLevel + // 234 - ReportGreenDimLevel + // 235 - ReportBlueDimLevel + // 236 - ReportWhiteDimLevel + // 237 - ReportAmberDimLevel + // 238 - ReportFreecolourDimLevel + // 239 - ReportRgbwafControl + // 240 - ReportColourType + // If, for colour type RGBWAF, more output channels are assigned to one colour (Red, Green, Blue, White, Amber or Freecolour) and the actual levels + // of these output channels are different the answer to that query shall be “MASK”. + // For all other DTR values and for unsupported colour types no answer shall be sent and neither DTR1 nor the DTR shall be changed. + // NOTE 1 The actual level of an output channel can be queried by linking only this output channel and sending QUERY ACTUAL LEVEL. + // NOTE 2 A control device should always use command 160 (“QUERY ACTUAL LEVEL”) to update the report colour setting before querying it. + // NOTE 3 A value of “MASK” for any of “x-COORDINATE PRIMARY N”, “y-COORDINATE PRIMARY N” or “TY PRIMARY N” means that this primary is + // undefined and calibration is needed. +#define DALI_209_QUERY_RGBWAF_CONTROL 0x00FB // 251 - RGBWAFControl contains further information about the assignment between output channel and color. + // bit 0 - Output channel 0 / red + // bit 1 - Output channel 1 / green + // bit 2 - Output channel 2 / blue + // bit 3 - Output channel 3 / white + // bit 4 - Output channel 4 / amber + // bit 5 - Output channel 5 / free selectable color + // bit 6..7 - 0 = channel control + // 1 = color control + // 2 = standardized color control + // 3 = reserved + // If an output channel/colour is not supported the appropriate bit shall read '0' +#define DALI_209_QUERY_ASSIGNED_COLOUR 0x00FC // 252 - Returns the color assigned to the specified output channel (DTR0 = 0...5). If a non-existent channel number is specified, 255 (MASK) is returned. (Uses DTR0) + // Assigned colour for a given channel (as specified in DTR0). Refer to Command 252 "QUERY ASSIGNED COLOUR". + // Note that a response may indicate an assigned channel, or could also be "MASK" if the queried channel is not supported or is invalid. + // value 0 - No color assigned + // value 1 - Red + // value 2 - Green + // value 3 - Blue + // value 4 - White + // value 5 - Amber + // value 6 - Freely selectable color +#define DALI_209_RESERVED253 0x00FD // 253 - [Reserved] +#define DALI_209_RESERVED254 0x00FE // 254 - [Reserved] +#define DALI_209_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +/*-------------------------------------------------------------------------------------------*\ + * DALI Application extended commands for IEC62386 part 210 = DT9 - Send as second byte + * Sequencer +\*-------------------------------------------------------------------------------------------*/ + +// Application extended query commands - Send as second byte +#define DALI_210_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - The version number of the extended support. + // This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored. + // Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number. + // Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin. + +#endif // _XDRV75_DALI_H_ +#endif // USE_DALI diff --git a/tasmota/tasmota_xdrv_driver/xdrv_75_dali.ino b/tasmota/tasmota_xdrv_driver/xdrv_75_dali.ino index 8386ec603..f98bcb71f 100644 --- a/tasmota/tasmota_xdrv_driver/xdrv_75_dali.ino +++ b/tasmota/tasmota_xdrv_driver/xdrv_75_dali.ino @@ -15,7 +15,47 @@ You should have received a copy of the GNU General Public License along with this program. If not, see . +*/ +#ifdef USE_DALI +/*********************************************************************************************\ + * DALI support for Tasmota + * + * Available commands: + * or = 0..255 or 0x00..0xFF + 256/0x100 for optional repeat (send twice) + * or = 0..255 or 0x00..0xFF - Both decimal and hexadecimal is supported + * = 0 - DALI default + * = 1..64 - DALI short address + 1 + * = 101..116 - DALI group + 101 + *
= 6, 8 - DALI Device Type specific extended command + * DaliSend , - Execute DALI code and do not expect a DALI backward frame + * DaliSend
,, - Execute DALI extended code for DT and do not expect a DALI backward frame + * DaliSend <0xA3>,,, - Set DALI parameter using DTR0 and do not expect a DALI backward frame + * DaliQuery , - Execute DALI code and report result (DALI backward frame) + * DaliQuery
,, - Execute DALI extended code for DT and report result (DALI backward frame) + * DaliScan 1|2 - Reset (0) or (1)/and commission device short addresses + * DaliGear 1..64 - Set max short address to speed up scanning - default 64 + * DaliGroup<1..16> [+]|-,... - Add(+) or Remove(-) devices to/from group + * DaliPower|| 0..254 - Control power (0 = Off, 1 = Last dimmer, 2 = Toggle, 3..254 = absolute light brightness) + * DaliDimmer|| 0..100 - Control dimmer (0 = Off, 1..100 = precentage of brightness) + * DaliLight 0|1 - Enable Tasmota light control for DaliTarget device - default 1 + * DaliTarget || - Set Tasmota light control device (0, 1..64, 101..116) - default 0 + * + * DALI background information + * Address type Address byte + * ------------------ -------------------- + * Broadcast address 1111111S + * 64 short address 0AAAAAAS + * 16 group address 100AAAAS + * Special command 101CCCC1 to 110CCCC1 + * A = Address bit, S = 0 Direct Arc Power control, S = 1 Command, C = Special command + * + * Shelly DALI Dimmer Gen3 (ESP32C3-8M) - GPIO3 controls DALI power. In following template it is always ON. Max output is 16V/10mA (= 5 DALI gear) + * Template {"NAME":"Shelly DALI Dimmer Gen3","GPIO":[34,4736,0,3840,11360,11392,128,129,0,1,576,0,0,0,0,0,0,0,0,1,1,1],"FLAG":0,"BASE":1} + * AdcGpio1 10000,10000,4000 <- Temperature parameters + * Backlog ButtonTopic 0; SetOption1 1; SetOption11 0; SetOption32 20; DimmerStep 5; LedTable 0 + * rule1 on button1#state=2 do dimmer + endon on button2#state=2 do dimmer - endon on button1#state=3 do power 2 endon on button2#state=3 do power 2 endon + * -------------------------------------------------------------------------------------------- Version yyyymmdd Action Description -------------------------------------------------------------------------------------------- @@ -56,44 +96,6 @@ - Refactor command `DaliPower 0..254` controlling Broadcast devices - Add command `DaliDimmer 0..254` controlling Broadcast devices 0.0.0.1 20221027 publish - Initial version by Andrei Kazmirtsuk aka eeak -*/ - -#ifdef USE_DALI - -/*********************************************************************************************\ - * DALI support for Tasmota - * - * Available commands: - * or = 0..255 or 0x00..0xFF + 256/0x100 for optional repeat (send twice) - * or = 0..255 or 0x00..0xFF - Both decimal and hexadecimal is supported - * = 0 - DALI default - * = 1..64 - DALI short address + 1 - * = 101..116 - DALI group + 101 - * DaliSend , - Execute DALI code and do not expect a DALI backward frame - * DaliSend <0xA3>,,, - Set DALI parameter using DTR0 and do not expect a DALI backward frame - * DaliQuery , - Execute DALI code and report result (DALI backward frame) - * DaliScan 1|2 - Reset (0) or (1)/and commission device short addresses - * DaliGear 1..64 - Set max short address to speed up scanning - default 64 - * DaliGroup<1..16> [+]|-,... - Add(+) or Remove(-) devices to/from group - * DaliPower|| 0..254 - Control power (0 = Off, 1 = Last dimmer, 2 = Toggle, 3..254 = absolute light brightness) - * DaliDimmer|| 0..100 - Control dimmer (0 = Off, 1..100 = precentage of brightness) - * DaliLight 0|1 - Enable Tasmota light control for DaliTarget device - default 1 - * DaliTarget || - Set Tasmota light control device (0, 1..64, 101..116) - default 0 - * - * DALI background information - * Address type Address byte - * ------------------ -------------------- - * Broadcast address 1111111S - * 64 short address 0AAAAAAS - * 16 group address 100AAAAS - * Special command 101CCCC1 to 110CCCC1 - * A = Address bit, S = 0 Direct Arc Power control, S = 1 Command, C = Special command - * - * Shelly DALI Dimmer Gen3 (ESP32C3-8M) - GPIO3 controls DALI power. In following template it is always ON. Max output is 16V/10mA (= 5 DALI gear) - * Template {"NAME":"Shelly DALI Dimmer Gen3","GPIO":[34,4736,0,3840,11360,11392,128,129,0,1,576,0,0,0,0,0,0,0,0,1,1,1],"FLAG":0,"BASE":1} - * AdcGpio1 10000,10000,4000 <- Temperature parameters - * Backlog ButtonTopic 0; SetOption1 1; SetOption11 0; SetOption32 20; DimmerStep 5; LedTable 0 - * rule1 on button1#state=2 do dimmer + endon on button2#state=2 do dimmer - endon on button1#state=3 do power 2 endon on button2#state=3 do power 2 endon \*********************************************************************************************/ #define XDRV_75 75 @@ -113,214 +115,9 @@ #define DALI_DEBUG_PIN 4 // Debug GPIO #endif -/*-------------------------------------------------------------------------------------------*\ - * DALI Commands - Send as first byte -\*-------------------------------------------------------------------------------------------*/ +#include "include/xdrv_75_dali.h" -// Address types - Send as first byte -#define DALI_SHORT_ADDRESS0 0x0000 // 0b00000000 0 - First short address -#define DALI_SHORT_ADDRESS1 0x0002 // 0b00000010 1 - Next short address -#define DALI_SHORT_ADDRESS63 0x007E // 0b01111110 63 - Last short address -#define DALI_GROUP_ADDRESS0 0x0080 // 0b10000000 0 - First group address -#define DALI_GROUP_ADDRESS1 0x0082 // 0b10000010 1 - Next group address -#define DALI_GROUP_ADDRESS15 0x009E // 0b10011110 15 - Last group address - -// Special commands - Send as first byte -#define DALI_TERMINATE 0x00A1 // 256 - Releases the INITIALISE state. -#define DALI_DATA_TRANSFER_REGISTER0 0x00A3 // 257 - Stores the data XXXX XXXX to the DTR(DTR0). -#define DALI_INITIALISE 0x01A5 // 258 REPEAT - Sets the slave to the INITIALISE status for15 minutes. Commands 259 to 270 are enabled only for a slave in this status. -#define DALI_RANDOMISE 0x01A7 // 259 REPEAT - Generates a random address. -#define DALI_COMPARE 0x00A9 // 260 - Is the random address smaller or equal to the search address? -#define DALI_WITHDRAW 0x00AB // 261 - Excludes slaves for which the random address and search address match from the Compare process. -#define DALI_RESERVED262 0x00AD // 262 - [Reserved] -#define DALI_PING 0x00AF // 263 - DALI-2 Ignores in the slave. -#define DALI_SEARCHADDRH 0x00B1 // 264 - Specifies the higher 8 bits of the search address. -#define DALI_SEARCHADDRM 0x00B3 // 265 - Specifies the middle 8 bits of the search address. -#define DALI_SEARCHADDRL 0x00B5 // 266 - Specifies the lower 8 bits of the search address. -#define DALI_PROGRAM_SHORT_ADDRESS 0x00B7 // 267 - The slave shall store the received 6-bit address (AAA AAA) as a short address if it is selected. -#define DALI_VERIFY_SHORT_ADDRESS 0x00B9 // 268 - Is the short address AAA AAA? -#define DALI_QUERY_SHORT_ADDRESS 0x00BB // 269 - What is the short address of the slaveNote 2being selected? -#define DALI_PHYSICAL_SELECTION 0x00BD // 270 - not DALI-2 Sets the slave to Physical Selection Mode and excludes the slave from the Compare process. (Excluding IEC62386-102ed2.0) -#define DALI_RESERVED271 0x00BF // 271 - [Reserved] - -// Extending special commands - Send as first byte -#define DALI_ENABLE_DEVICE_TYPE_X 0x00C1 // 272 - Adds the device XXXX (a special device). -#define DALI_DATA_TRANSFER_REGISTER1 0x00C3 // 273 - Stores data XXXX into DTR1. -#define DALI_DATA_TRANSFER_REGISTER2 0x00C5 // 274 - Stores data XXXX into DTR2. -#define DALI_WRITE_MEMORY_LOCATION 0x00C7 // 275 - Write data into the specified address of the specified memory bank. (There is BW) (DTR(DTR0)：address, DTR1：memory bank number) -#define DALI_WRITE_MEMORY_LOCATION_NO_REPLY 0x00C9 // 276 - DALI-2 Write data into the specified address of the specified memory bank. (There is no BW) (DTR(DTR0)：address, TR1：memory bank number) -#define DALI_RESERVED277 0x00CB // 277 - [Reserved] -#define DALI_RESERVED349 0x00FD // 349 - [Reserved] - -// Address type - Send as first byte -#define DALI_BROADCAST_DP 0x00FE // 0b11111110 254 - Broadcast address - -/*-------------------------------------------------------------------------------------------*\ - * DALI Commands - Send as second byte -\*-------------------------------------------------------------------------------------------*/ - -// Control commands - Send as second byte without repeat -#define DALI_OFF 0x0000 // 0 - Turns off lighting. -#define DALI_UP 0x0001 // 1 - Increases the lighting control level for 200 ms according to the Fade rate. -#define DALI_DOWN 0x0002 // 2 - Decreases the lighting control level for 200 ms according to the Fade rate. -#define DALI_STEP_UP 0x0003 // 3 - Increments the lighting control level (without fade). -#define DALI_STEP_DOWN 0x0004 // 4 - Decrements the lighting control level (without fade). -#define DALI_RECALL_MAX_LEVEL 0x0005 // 5 - Maximizes the lighting control level (without fade). -#define DALI_RECALL_MIN_LEVEL 0x0006 // 6 - Minimizes the lighting control level (without fade) -#define DALI_STEP_DOWN_AND_OFF 0x0007 // 7 - Decrements the lighting control level and turns off lighting if the level is at the minimum (without fade). -#define DALI_ON_AND_STEP_UP 0x0008 // 8 - Increments the lighting control level and turns on lighting if lighting is off (with fade). -#define DALI_ENABLE_DAPC_SEQUENCE 0x0009 // 9 - It shows the repeat start of the DAPC command. -#define DALI_GO_TO_LAST_ACTIVE_LEVEL 0x000A // 10 - DALI-2 Adjusts the lighting control level to the last light control level according to the Fade time. -#define DALI_RESERVED11 0x000B // 11 - [Reserved] -#define DALI_RESERVED15 0x000F // 15 - [Reserved] -#define DALI_GO_TO_SCENE0 0x0010 // 16 - Adjusts the lighting control level for Scene XXXX according to the fade time. -#define DALI_GO_TO_SCENE15 0x001F // 31 - Adjusts the lighting control level for Scene XXXX according to the fade time. - -// Configuration commands - Send as second byte with repeat -#define DALI_RESET 0x0020 // 32 - Makes a slave an RESET state. -#define DALI_STORE_ACTUAL_LEVEL_IN_THE_DTR0 0x0021 // 33 - Saves the current lighting control level to the DTR (DTR0). -#define DALI_SAVE_PERSISTENT_VARIABLES 0x0022 // 34 - DALI-2 Saves a variable in nonvolatile memory (NVM). -#define DALI_SET_OPERATING_MODE 0x0023 // 35 - DALI-2 Sets data of DTR0 as an operating mode. -#define DALI_RESET_MEMORY_BANK 0x0024 // 36 - DALI-2 Changes to the reset value the specified memory bank in DTR0. -#define DALI_IDENTIFY_DEVICE 0x0025 // 37 - DALI-2 Starts the identification state of the device. -#define DALI_RESERVED38 0x0026 // 38 - [Reserved] -#define DALI_RESERVED41 0x0029 // 41 - [Reserved] -#define DALI_SET_MAX_LEVEL 0x002A // 42 - Specifies the DTR data as the maximum lighting control level. -#define DALI_SET_MIN_LEVEL 0x002B // 43 - Specifies the DTR data as the minimum lighting control level. -#define DALI_SET_SYSTEM_FAILURE_LEVEL 0x002C // 44 - Specifies the DTR data as the "FAILURELEVEL". -#define DALI_SET_POWER_ON_LEVEL 0x002D // 45 - Specifies the DTR data as the "POWER ONLEVEL". -#define DALI_SET_FADE_TIME 0x002E // 46 - Specifies the DTR data as the Fade time. -#define DALI_SET_FADE_RATE 0x002F // 47 - Specifies the DTR data as the Fade rate. -#define DALI_SET_EXTENDED_FADE_TIME 0x0030 // 48 - DALI-2 Specifies the DTR data as the Extended Fade Time. -#define DALI_RESERVED49 0x0031 // 49 - [Reserved] -#define DALI_RESERVED63 0x003F // 63 - [Reserved] -#define DALI_SET_SCENE0 0x0040 // 64 - Specifies the DTR data as Scene XXXX. -#define DALI_SET_SCENE15 0x004F // 79 - Specifies the DTR data as Scene XXXX. -#define DALI_REMOVE_FROM_SCENE0 0x0050 // 80 - Deletes the Scene XXXX setting. (Specifies 1111 1111 for the scene register.) -#define DALI_REMOVE_FROM_SCENE15 0x005F // 95 - Deletes the Scene XXXX setting. (Specifies 1111 1111 for the scene register.) -#define DALI_ADD_TO_GROUP0 0x0060 // 96 - Adds the slave to Group XXXX. -#define DALI_ADD_TO_GROUP15 0x006F // 111 - Adds the slave to Group XXXX. -#define DALI_REMOVE_FROM_GROUP0 0x0070 // 112 - Deletes the slave from Group XXXX. -#define DALI_REMOVE_FROM_GROUP15 0x007F // 127 - Deletes the slave from Group XXXX. -#define DALI_SET_SHORT_ADDRESS 0x0080 // 128 - Specifies the DTR data as a Short Address. -#define DALI_ENABLE_WRITE_MEMORY 0x0081 // 129 - Allows writing of the memory bank. -#define DALI_RESERVED130 0x0082 // 130 - [Reserved] -#define DALI_RESERVED143 0x008F // 143 - [Reserved] - -// Query commands - Send as second byte -#define DALI_QUERY_STATUS 0x0090 // 144 - Returns "STATUS INFORMATION" -#define DALI_QUERY_CONTROL_GEAR_PRESENT 0x0091 // 145 - Is there a slave that can communicate? -#define DALI_QUERY_LAMP_FAILURE 0x0092 // 146 - Is there a lamp problem? -#define DALI_QUERY_LAMP_POWER_ON 0x0093 // 147 - Is a lamp on? -#define DALI_QUERY_LIMIT_ERROR 0x0094 // 148 - Is the specified lighting control level out of the range from the minimum to the maximum values? -#define DALI_QUERY_RESET_STATE 0x0095 // 149 - Is the slave in 'RESET STATE'? -#define DALI_QUERY_MISSING_SHORT_ADDRESS 0x0096 // 150 - Does the slave not have a short address? -#define DALI_QUERY_VERSION_NUMBER 0x0097 // 151 - What is the corresponding IEC standard number? -#define DALI_QUERY_CONTENT_DTR0 0x0098 // 152 - What is the DTR content? -#define DALI_QUERY_DEVICE_TYPE 0x0099 // 153 - What is the device type? (fluorescent lamp:0000 0000) (IEC62386-207 is 6 fixed) -#define DALI_QUERY_PHYSICAL_MINIMUM_LEVEL 0x009A // 154 - What is the minimum lighting control level specified by the hardware? -#define DALI_QUERY_POWER_FAILURE 0x009B // 155 - Has the slave operated without the execution of reset-command or the adjustment of the lighting control level? -#define DALI_QUERY_CONTENT_DTR1 0x009C // 156 - What is the DTR1 content? -#define DALI_QUERY_CONTENT_DTR2 0x009D // 157 - What is the DTR2 content? -#define DALI_QUERY_OPERATING_MODE 0x009E // 158 - DALI-2 What is the Operating Mode? -#define DALI_QUERY_LIGHT_SOURCE_TYPE 0x009F // 159 - DALI-2 What is the Light source type? -#define DALI_QUERY_ACTUAL_LEVEL 0x00A0 // 160 - What is the "ACTUAL LEVEL" (the current lighting control level)? -#define DALI_QUERY_MAX_LEVEL 0x00A1 // 161 - What is the maximum lighting control level? -#define DALI_QUERY_MIN_LEVEL 0x00A2 // 162 - What is the minimum lighting control level? -#define DALI_QUERY_POWER_ON_LEVEL 0x00A3 // 163 - What is the "POWER ON LEVEL" (the lighting control level when the power is turned on)? -#define DALI_QUERY_SYSTEM_FAILURE_LEVEL 0x00A4 // 164 - What is the "SYSTEM FAILURE LEVEL" (the lighting control level when a failure occurs)? -#define DALI_QUERY_FADE_TIME_FADE_RATE 0x00A5 // 165 - What are the Fade time and Fade rate? -#define DALI_QUERY_MANUFACTURER_SPECIFIC_MODE 0x00A6 // 166 - DALI-2 What is the Specific Mode? -#define DALI_QUERY_NEXT_DEVICE_TYPE 0x00A7 // 167 - DALI-2 What is the next Device Type? -#define DALI_QUERY_EXTENDED_FADE_TIME 0x00A8 // 168 - DALI-2 What is the Extended Fade Time? -#define DALI_QUERY_CONTROL_GEAR_FAILURE 0x00A9 // 169 - DALI-2 Does a slave have the abnormality? -#define DALI_RESERVED170 0x00AA // 170 - [Reserved] -#define DALI_RESERVED175 0x00AF // 175 - [Reserved] -#define DALI_QUERY_SCENE0_LEVEL 0x00B0 // 176 - What is the lighting control level for SCENE XXXX? -#define DALI_QUERY_GROUPS_0_7 0x00C0 // 192 - Does the slave belong to a group among groups 0 to 7? (Each bit corresponds to a group.) -#define DALI_QUERY_GROUPS_8_15 0x00C1 // 193 - Does the slave belong to a group among groups 8 to 15? (Each bit corresponds to a group.) -#define DALI_QUERY_RANDOM_ADDRESS_H 0x00C2 // 194 - What are the higher 8 bits of the random address? -#define DALI_QUERY_RANDOM_ADDRESS_M 0x00C3 // 195 - What are the middle 8 bits of the random address? -#define DALI_QUERY_RANDOM_ADDRESS_L 0x00C4 // 196 - What are the lower 8 bits of the random address? -#define DALI_READ_MEMORY_LOCATION 0x00C5 // 197 - What is the memory location content? -#define DALI_RESERVED198 0x00C6 // 198 - [Reserved] -#define DALI_RESERVED223 0x00DF // 223 - [Reserved] - -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 201 = DT0 - Send as second byte - * Standard device like fluorescent lamps -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 202 = DT1 - Send as second byte - * Device for emergency lighting -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 203 = DT2 - Send as second byte - * Device for discharge lamps excluding fluorescent lamps -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 204 = DT3 - Send as second byte - * Device for low-voltage halogen lamps -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 205 = DT4 - Send as second byte - * Device for dimming incandescent lamps -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 206 = DT5 - Send as second byte - * Device for converting digital signales into DC signals -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 207 = DT6 - Send as second byte - * Device for Light Emitting Diodes (LEDs) -\*-------------------------------------------------------------------------------------------*/ - -// Application extended configuration commands - Send as second byte -#define DALI_REFERENCE_SYSTEM_POWER 0x00E0 // 224 - IEC62386-207 Starts power measurement. -#define DALI_ENABLE_CURRENT_PROTECTOR 0x00E1 // 225 - IEC62386-207 Enables the current protection. -#define DALI_DISABLE_CURRENT_PROTECTOR 0x00E2 // 226 - IEC62386-207 Disables the current protection. -#define DALI_SELECT_DIMMING_CURVE 0x00E3 // 227 - IEC62386-207 Selects Dimming curve. -#define DALI_STORE_DTR_AS_FAST_FADE_TIME 0x00E4 // 228 - IEC62386-207 Sets the DTR of the data as Fast Fade Time. -#define DALI_RESERVED229 0x00E5 // 229 - [Reserved] -#define DALI_RESERVED236 0x00EC // 236 - [Reserved] - -// Application extended query commands - Send as second byte -#define DALI_QUERY_GEAR_TYPE 0x00ED // 237 - IEC62386-207 Returns ‘GEAR TYPE’ -#define DALI_QUERY_DIMMING_CURVE 0x00EE // 238 - IEC62386-207 Returns ’Dimming curve’in use -#define DALI_QUERY_POSSIBLE_OPERATING_MODE 0x00EF // 239 - IEC62386-207 Returns ‘POSSIBLE OPERATING MODE’ -#define DALI_QUERY_FEATURES 0x00F0 // 240 - IEC62386-207 Returns ‘FEATURES’ -#define DALI_QUERY_FAILURE_STATUS 0x00F1 // 241 - IEC62386-207 Returns ‘FAILURE STATUS’ -#define DALI_QUERY_SHORT_CIRCUIT 0x00F2 // 242 - IEC62386-207 Returns bit0 short circuit of ‘FAILURE STATUS’ -#define DALI_QUERY_OPEN_CIRCUIT 0x00F3 // 243 - IEC62386-207 Returns bit1 open circuit of ‘FAILURE STATUS’ -#define DALI_QUERY_LOAD_DECREASE 0x00F4 // 244 - IEC62386-207 Returns bit2 load decrease of ‘FAILURE STATUS’ -#define DALI_QUERY_LOAD_INDREASE 0x00F5 // 245 - IEC62386-207 Returns bit3 load increase of‘FAILURE STATUS’ -#define DALI_QUERY_CURRENT_PROTECTOR_ACTIVE 0x00F6 // 246 - IEC62386-207 Returns bit4 current protector active of ‘FAILURE STATUS’ -#define DALI_QUERY_THERMAL_SHUTDOWN 0x00F7 // 247 - IEC62386-207 Returns bit5 thermal shut down of ‘FAILURE STATUS’ -#define DALI_QUERY_THERMAL_OVERLOAD 0x00F8 // 248 - IEC62386-207 Returns bit6 thermal overload with light level reduction of ‘FAILURE STATUS’ -#define DALI_QUERY_REFARENCE_RUNNING 0x00F9 // 249 - IEC62386-207 Returns whetherReference System Power is in operation. -#define DALI_QUERY_REFERENCE_MEASURMENT_FAILED 0x00FA // 250 - IEC62386-207 Returns bit7 reference measurement failed of ‘FAILURE STATUS’ -#define DALI_QUERY_CURRENT_PROTECTOR_ENABLE 0x00FB // 251 - IEC62386-207 Returns state of Curent protector -#define DALI_QUERY_OPERATING_MODE2 0x00FC // 252 - IEC62386-207 Returns ‘OPERATING MODE’ -#define DALI_QUERY_FAST_FADE_TIME 0x00FD // 253 - IEC62386-207 Returns set Fast fade time. -#define DALI_QUERY_MIN_FAST_FADE_TIME 0x00FE // 254 - IEC62386-207 Returns set Minimum fast fade time -#define DALI_QUERY_EXTENDED_VERSION_NUMBER 0x00FF // 255 - IEC62386-207 The version number of the extended support? IEC62386-207: 1, Other: NO(no response) - -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 208 = DT7 - Send as second byte - * Device for switching functions -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 209 = DT8 - Send as second byte - * Device for controlling color and color temperature -\*-------------------------------------------------------------------------------------------*/ -/*-------------------------------------------------------------------------------------------*\ - * DALI Application extended commands for IEC62386 part 210 = DT9 - Send as second byte - * Sequencer -\*-------------------------------------------------------------------------------------------*/ - -/*-------------------------------------------------------------------------------------------*/ - -#define DALI_MAX_STORED 17 // Store broadcast and group states +#define DALI_MAX_STORED 17 // Store broadcast and group states #define DALI_TOPIC "DALI" #define D_PRFX_DALI "Dali" @@ -371,6 +168,28 @@ struct DALI { * DALI low level \*********************************************************************************************/ +uint32_t DaliKelvinToMirek(uint32_t kelvin) { + if (kelvin < 16) { + return 65535; + } + if (kelvin > 1000000) { + return 0; + } + return 1000000 / kelvin; +} + +uint32_t DaliMirekToKelvin(uint32_t mirek) { + if (mirek <= 0) { + return 1000001; + } + if (mirek >= 65535) { + return 0; + } + return 1000000 / mirek; +} + +/*-------------------------------------------------------------------------------------------*/ + uint32_t DaliTarget2Address(void) { // 1..64 = Short address // 101..116 = Group address @@ -668,8 +487,8 @@ bool DaliSetValue(uint32_t adr, uint32_t getcmd, uint32_t setcmd, uint32_t v) { // Set a parameter value, returns true on success int current_v = DaliSendWaitResponse(adr, getcmd); // Get current parameter value if (current_v == v) { return true; } // Already set - DaliSendData(DALI_DATA_TRANSFER_REGISTER0, v); // Store value in DTR - int dtr = DaliSendWaitResponse(adr, DALI_QUERY_CONTENT_DTR0); // Get DTR value + DaliSendData(DALI_102_SET_DTR0, v); // Store value in DTR + int dtr = DaliSendWaitResponse(adr, DALI_102_QUERY_CONTENT_DTR0); // Get DTR value if (dtr != v) { return false; } DaliSendData(adr, setcmd); // Set parameter value = DTR current_v = DaliSendWaitResponse(adr, getcmd); // Get current parameter value @@ -678,23 +497,23 @@ bool DaliSetValue(uint32_t adr, uint32_t getcmd, uint32_t setcmd, uint32_t v) { } bool DaliSetOperatingMode(uint32_t adr, uint32_t v) { - return DaliSetValue(adr, DALI_QUERY_OPERATING_MODE, DALI_SET_OPERATING_MODE, v); + return DaliSetValue(adr, DALI_102_QUERY_OPERATING_MODE, DALI_102_SET_OPERATING_MODE, v); } bool DaliSetMaxLevel(uint32_t adr, uint32_t v) { - return DaliSetValue(adr, DALI_QUERY_MAX_LEVEL, DALI_SET_MAX_LEVEL, v); + return DaliSetValue(adr, DALI_102_QUERY_MAX_LEVEL, DALI_102_SET_MAX_LEVEL, v); } bool DaliSetMinLevel(uint32_t adr, uint32_t v) { - return DaliSetValue(adr, DALI_QUERY_MIN_LEVEL, DALI_SET_MIN_LEVEL, v); + return DaliSetValue(adr, DALI_102_QUERY_MIN_LEVEL, DALI_102_SET_MIN_LEVEL, v); } bool DaliSetSystemFailureLevel(uint32_t adr, uint32_t v) { - return DaliSetValue(adr, DALI_QUERY_SYSTEM_FAILURE_LEVEL, DALI_SET_SYSTEM_FAILURE_LEVEL, v); + return DaliSetValue(adr, DALI_102_QUERY_SYSTEM_FAILURE_LEVEL, DALI_102_SET_SYSTEM_FAILURE_LEVEL, v); } bool DaliSetPowerOnLevel(uint32_t adr, uint32_t v) { - return DaliSetValue(adr, DALI_QUERY_POWER_ON_LEVEL, DALI_SET_POWER_ON_LEVEL, v); + return DaliSetValue(adr, DALI_102_QUERY_POWER_ON_LEVEL, DALI_102_SET_POWER_ON_LEVEL, v); } /*-------------------------------------------------------------------------------------------*/ @@ -702,7 +521,7 @@ bool DaliSetPowerOnLevel(uint32_t adr, uint32_t v) { uint32_t DaliGearPresent(void) { uint32_t count = 0; for (uint32_t sa = 0; sa < Dali->max_short_address; sa++) { // Scanning 64 addresses takes about 2500 ms - if (DaliSendWaitResponse(sa << 1 | 1, DALI_QUERY_CONTROL_GEAR_PRESENT, 20) >= 0) { + if (DaliSendWaitResponse(sa << 1 | 1, DALI_102_QUERY_CONTROL_GEAR_PRESENT, 20) >= 0) { count++; } } @@ -713,12 +532,12 @@ uint32_t DaliGearPresent(void) { void DaliInitLight(void) { // Taken from Shelly Dali Dimmer ;-) - DaliSendData(DALI_DATA_TRANSFER_REGISTER0, DALI_INIT_FADE); // Fade x second - DaliSendData(0xFF, DALI_SET_FADE_TIME); - DaliSendData(DALI_DATA_TRANSFER_REGISTER0, 0); // Power off after gear power restore - DaliSendData(0xFF, DALI_SET_POWER_ON_LEVEL); - DaliSendData(DALI_DATA_TRANSFER_REGISTER0, 0xFE); // Reset all but short circuit - DaliSendData(0xFF, DALI_SET_SYSTEM_FAILURE_LEVEL); + DaliSendData(DALI_102_SET_DTR0, DALI_INIT_FADE); // Fade x second + DaliSendData(0xFF, DALI_102_SET_FADE_TIME); + DaliSendData(DALI_102_SET_DTR0, 0); // Power off after gear power restore + DaliSendData(0xFF, DALI_102_SET_POWER_ON_LEVEL); + DaliSendData(DALI_102_SET_DTR0, 0xFE); // Reset all but short circuit + DaliSendData(0xFF, DALI_102_SET_SYSTEM_FAILURE_LEVEL); } /*********************************************************************************************\ @@ -729,18 +548,18 @@ void DaliInitLight(void) { void DaliSetSearchAddress(uint32_t adr) { // Set search address - DaliSendData(DALI_SEARCHADDRH, adr>>16); - DaliSendData(DALI_SEARCHADDRM, adr>>8); - DaliSendData(DALI_SEARCHADDRL, adr); + DaliSendData(DALI_102_SEARCHADDRH, adr>>16); + DaliSendData(DALI_102_SEARCHADDRM, adr>>8); + DaliSendData(DALI_102_SEARCHADDRL, adr); } /*-------------------------------------------------------------------------------------------*/ void DaliSetSearchAddressDifference(uint32_t adr_new, uint32_t adr_current) { // Set search address, but set only changed bytes (takes less time) - if ( (uint8_t)(adr_new>>16) != (uint8_t)(adr_current>>16) ) DaliSendData(DALI_SEARCHADDRH, adr_new>>16); - if ( (uint8_t)(adr_new>>8) != (uint8_t)(adr_current>>8) ) DaliSendData(DALI_SEARCHADDRM, adr_new>>8); - if ( (uint8_t)(adr_new) != (uint8_t)(adr_current) ) DaliSendData(DALI_SEARCHADDRL, adr_new); + if ( (uint8_t)(adr_new>>16) != (uint8_t)(adr_current>>16) ) DaliSendData(DALI_102_SEARCHADDRH, adr_new>>16); + if ( (uint8_t)(adr_new>>8) != (uint8_t)(adr_current>>8) ) DaliSendData(DALI_102_SEARCHADDRM, adr_new>>8); + if ( (uint8_t)(adr_new) != (uint8_t)(adr_current) ) DaliSendData(DALI_102_SEARCHADDRL, adr_new); } /*-------------------------------------------------------------------------------------------*/ @@ -752,7 +571,7 @@ bool DaliCompare() { while (retry > 0) { // Compare is true if we received any activity on the bus as reply. // Sometimes the reply is not registered... so only accept retry times 'no reply' as a real false compare - int rv = DaliSendWaitResponse(DALI_COMPARE, 0x00); + int rv = DaliSendWaitResponse(DALI_102_COMPARE, 0x00); if (rv == 0xFF) return true; // Yes reply if (rv == -2) return true; // Reply but collision retry--; @@ -792,7 +611,7 @@ uint32_t DaliFindAddress(void) { void DaliProgramShortAddress(uint8_t shortadr) { // The slave shall store the received 6-bit address (AAAAAA) as a short address if it is selected. - DaliSendData(DALI_PROGRAM_SHORT_ADDRESS, (shortadr << 1) | 0x01); + DaliSendData(DALI_102_PROGRAM_SHORT_ADDRESS, (shortadr << 1) | 0x01); AddLog(LOG_LEVEL_INFO, PSTR("DLI: Set short address %d"), shortadr +1); } @@ -805,21 +624,21 @@ uint32_t DaliCommission(uint8_t init_arg) { // init_arg=00000000 : all // init_arg=0AAAAAA1 : only for this shortadr // returns number of new short addresses assigned - DaliSendData(0xFF, DALI_RESET); // Turns ON all lights + DaliSendData(0xFF, DALI_102_RESET); // Turns ON all lights uint8_t arr[64]; uint32_t sa; for (sa = 0; sa < 64; sa++) { arr[sa] = 0; } - delay(450); - DaliSendData(DALI_DATA_TRANSFER_REGISTER0, 0xFF); - DaliSendData(0xFF, DALI_SET_SHORT_ADDRESS); - DaliSendData(DALI_TERMINATE, 0x00); // Terminate the DALI_INITIALISE command + delay(450); // It is not guaranteed that any commands will be received properly within the next 300ms + DaliSendData(DALI_102_SET_DTR0, 0xFF); + DaliSendData(0xFF, DALI_102_SET_SHORT_ADDRESS); + DaliSendData(DALI_102_TERMINATE, 0x00); // Terminate the DALI_102_INITIALISE command delay(15); // Start commissioning - DaliSendData(DALI_INITIALISE, init_arg); - DaliSendData(DALI_RANDOMISE, 0x00); - delay(65); // Need pause after RANDOMISE + DaliSendData(DALI_102_INITIALISE, init_arg); + DaliSendData(DALI_102_RANDOMISE, 0x00); + delay(100); // The new random address shall be available within a time period of 100ms. uint32_t cnt = 0; while (true) { // Find random addresses and assign unused short addresses @@ -833,15 +652,15 @@ uint32_t DaliCommission(uint8_t init_arg) { cnt++; DaliProgramShortAddress(sa); // Assign short address - DaliSendData(DALI_WITHDRAW, 0x00); // Remove the device from the search - DaliSendData(sa << 1, DALI_OFF); // Turns OFF latest short address light + DaliSendData(DALI_102_WITHDRAW, 0x00); // Remove the device from the search + DaliSendData(sa << 1, DALI_102_OFF); // Turns OFF latest short address light delay(1); OsWatchLoop(); // Feed blocked-loop watchdog } delay(100); - DaliSendData(DALI_TERMINATE, 0x00); // Terminate the DALI_INITIALISE command + DaliSendData(DALI_102_TERMINATE, 0x00); // Terminate the DALI_102_INITIALISE command #ifdef USE_LIGHT DaliInitLight(); @@ -1172,14 +991,14 @@ void CmndDaliGroup(void) { bool more = false; char temp[200] = { 0 }; if (XdrvMailbox.data_len) { - uint32_t command = DALI_ADD_TO_GROUP0; + uint32_t command = DALI_102_ADD_TO_GROUP0; temp[0] = '+'; if ('+' == XdrvMailbox.data[0]) { // Add devices XdrvMailbox.data++; XdrvMailbox.data_len--; } else if ('-' == XdrvMailbox.data[0]) { // Remove devices - command = DALI_REMOVE_FROM_GROUP0; + command = DALI_102_REMOVE_FROM_GROUP0; XdrvMailbox.data++; XdrvMailbox.data_len--; temp[0] = '-'; @@ -1200,10 +1019,10 @@ void CmndDaliGroup(void) { ResponseCmndIdxChar(temp); } } else { - uint32_t command = DALI_QUERY_GROUPS_0_7; + uint32_t command = DALI_102_QUERY_GROUPS_0_7; uint32_t bitmask = 1 << group; if (group > 7) { - command = DALI_QUERY_GROUPS_8_15; + command = DALI_102_QUERY_GROUPS_8_15; bitmask = 1 << group - 8; } for (uint32_t sa = 0; sa < Dali->max_short_address; sa++) { // Scanning 64 addresses takes about 2500 ms @@ -1237,11 +1056,12 @@ void CmndDaliGear(void) { void CmndDaliSend(void) { // Send command // Setting bit 8 will repeat command once - // DaliSend 0x1a5,255 - DALI Initialise (send twice) - // DaliSend 6,3,0xe2 - DALI DT6 (6) for address 1 (3) extended command disable current protector (0xE2 = 226) - // DaliSend 0x01,0xa3,0x2d,254 - Set Power On level + // DaliSend 0x1a5,255 - DALI Initialise (0xa5 + 0x100 = send twice) + // DaliSend 6,3,0xe2 - DALI DT6 (6) for address 1 (3) extended command disable current protector (0xe2) + // DaliSend 0x01,0xa3,0x2d,254 - Set Power On level (0x2d) for address 0 (0x01) to 254 only if Read Power On level (0xa3) is different uint32_t values[4] = { 0 }; uint32_t params = ParseParameters(4, values); + if (2 == params) { // Prepare for Extended command if ((values[1] >= 224) && (values[1] <= 255)) { // Extended command values[2] = values[1]; @@ -1251,7 +1071,7 @@ void CmndDaliSend(void) { } } if (3 == params) { // Set extended command mode - DaliSendWaitResponse(DALI_ENABLE_DEVICE_TYPE_X, values[0] &0xFF); // Enable Extended command + DaliSendWaitResponse(DALI_102_ENABLE_DEVICE_TYPE_X, values[0] &0xFF); // Enable Extended command values[0] = values[1]; values[1] = values[2]; params = 2; @@ -1276,7 +1096,7 @@ void CmndDaliQuery(void) { // Setting bit 8 will repeat command once // DaliQuery 0xff,0x90 - DALI Query status // DaliQuery 0xff,144 - DALI Query status - // DaliQuery 6,7,237 - DALI Query status using extended command from DT6 + // DaliQuery 6,7,237 - DALI DT6 (6) for address 3 (7) extended command query status (237) uint32_t values[3] = { 0 }; uint32_t params = ParseParameters(3, values); if (2 == params) { @@ -1288,7 +1108,7 @@ void CmndDaliQuery(void) { } } if (3 == params) { - DaliSendWaitResponse(DALI_ENABLE_DEVICE_TYPE_X, values[0] &0xFF); // Enable Extended command + DaliSendWaitResponse(DALI_102_ENABLE_DEVICE_TYPE_X, values[0] &0xFF); // Enable Extended command values[0] = values[1]; values[1] = values[2]; params = 2;