* fix: don't reset the device when coming out of deep sleep
* fix: move debug log message to inside the device validation
* Update xsns_110_max17043.ino
* add: update global battery percentage when max17043 reports new value
* Added a passive mode in sen5x sensor for parasitic installations. This skips reset & initialization of sensor on startup and reduces the polling to every 10 seconds to not interfere with and confuse the other I2C master on the bus, e.g. Ike* Vindstyrka.
* Removed obsolete updateCount. Cleanup.
* add: update DEBUG_THERMOSTAT to only control the virtual switch
Also, debug output is still generated but end user can control this debug level 3
* add: debug output of main controller parameters when thermostat enabled
Also, add units for debug outputs added to make them more intelligible
* Update xdrv_39_thermostat.ino
* add: debug message when sensor is detected as not alive
fix: display thermostat number in debug messages
* add: log message prefix string for thermostat
* Update xdrv_39_thermostat.ino
fix: typos in comments
add: debug messages
* add: debug prefix for thermostat
* add: debug prefix added to output lines
* fix: comment typos and small grammatical changes for clarity
* add: debug prefix 'THE' added to debug output
* Restart MAX17043 from the scratch
* revert change
* Changed battery capacity in charge (capacity is the Ah value of the battery, this degrades over time when battery ages)
* merge
* Changing xsns_109 to 110
* fix nr
* removed old xsns109
* Update I2CDEVICES.md
* clean-up usage of Interface
* New LWT on deepsleep
To allow better integration into HA LWT topic will report details of sleep status:
16:54:04.388 MQT: hm/tele/ESP_3284D1/LWT =
{"Sleep":{"Time":"2023-07-17T16:55:03","Sleep":1689612844,"Wakeup":1689612903}}
* Revert LWT back to non JSON
Send DeelSleep on LWT
Send Deepsleep parameters on topic DeepSleep
* Setting default for batteryLevel
* Enable BatteryPercentSet
Changing the battery level e.g. by rule
* Added Battery % to status message
* added battery_level_percent
* Added battery % support in STATE message
* Enable setting battery level
101 is reserved for power-plug. No battery Level reported
* Setting default for battery Level
101 is reserved for power plug
0..100 normal battery values
* Revert back LWT to Offline
Removed "DeepSleep" LWT status until further decision is made. Current implementation is technical sufficient for HA to detect a battery powered device
* Added discovery message after deepsleep change
* Added discovery for battery and deepsleep
This change will allow mqtt messages simpler by allowing something like
`publish cmnd/ir-bridge/IRHVAC {"Power": "On"}`.
The simpler format is required for working with mqtt clients like
iotMQTTPanel or similar on android.
Limitations:
- Requires full message be sent at-least once. I work around this with
a `system#boot` rule
- Gets messy with multiple devices. I have only one AC per room, and
this doesn't doesn't interfere with other IR devices.
TODO:
- [ ] Change the build flag `INCREMENTAL_IRAC`to a `SetOption`
- [ ] Persist `irac_prev_state` across reboots.
- [ ] Support multiple devices.
* IR: Added support for new A/C protocol fields
New fields introduced in IRremoteESP8266 v2.8.5:
1. Command (one of: [Control | Config | iFeel | Timer], default: Control) - allows to set IR command type (e.g. iFeel for no-beep ambient sensor report)
2. iFeel (boolean, default: false) - configures whether iFeel (ambient sensor temp. is used by the A/C unit)
3. SensorTemp - the ambient sensor temperature reading to send
Note:
- Fan setting via int is now 6-value (breaking change -> 6 is the new max)
* IR A/C: Model now pretty-printed to JSON
Model string is the default (falls back to int if n/a)
* IR A/C: Added separate JSON resp. per command type
* No change for "kControlCommand" (default/legacy).
* SensorReport/Timer/Config commands only contain relevant JSON nodes
Additionally:
Clock has time semantics (input: minutes, output: HH:MM), except for "config" mode,
where state.clock is used as ConfigKey and state.sleep is used as ConfigValue.
---------
Co-authored-by: Mateusz Bronk <2566147+mbronk@users.noreply.github.com>
* Added support for Dingtian Relay Board v3.6.10
* Output OE was never initialized
* Removed white spaces trying to fix language builds
* Fix for https://github.com/arendst/Tasmota/pull/18535#pullrequestreview-1406978097
* Fixed language builds
---------
Co-authored-by: JeroenSt <nospam@nospam.org>
