Tasmota/lib/IRremoteESP8266-2.5.2.03/src/ir_Argo.cpp

/*
Node MCU/ESP8266 Sketch to emulate Argo Ulisse 13 DCI remote
Controls Argo Ulisse 13 DCI A/C
Copyright 2017 Schmolders
*/

#include "ir_Argo.h"
#include <algorithm>
#include "IRremoteESP8266.h"
#include "IRutils.h"

// Constants
// using SPACE modulation. MARK is always const 400u
const uint16_t kArgoHdrMark = 6400;
const uint16_t kArgoHdrSpace = 3300;
const uint16_t kArgoBitMark = 400;
const uint16_t kArgoOneSpace = 2200;
const uint16_t kArgoZeroSpace = 900;

#if SEND_ARGO
// Send an Argo A/C message.
//
// Args:
//   data: An array of kArgoStateLength bytes containing the IR command.
//
// Status: ALPHA / Untested.

void IRsend::sendArgo(unsigned char data[], uint16_t nbytes, uint16_t repeat) {
  // Check if we have enough bytes to send a proper message.
  if (nbytes < kArgoStateLength) return;
  // TODO(kaschmo): validate
  sendGeneric(kArgoHdrMark, kArgoHdrSpace, kArgoBitMark, kArgoOneSpace,
              kArgoBitMark, kArgoZeroSpace, 0, 0,  // No Footer.
              data, nbytes, 38, false, repeat, kDutyDefault);
}
#endif  // SEND_ARGO

IRArgoAC::IRArgoAC(uint16_t pin) : _irsend(pin) { stateReset(); }

void IRArgoAC::begin() { _irsend.begin(); }

#if SEND_ARGO
void IRArgoAC::send() {
  checksum();  // Create valid checksum before sending
  _irsend.sendArgo(argo);
}
#endif  // SEND_ARGO

void IRArgoAC::checksum() {
  uint8_t sum = 2;  // Corresponds to byte 11 being constant 0b01
  uint8_t i;

  // Only add up bytes to 9. byte 10 is 0b01 constant anyway.
  // Assume that argo array is MSB first (left)
  for (i = 0; i < 10; i++) sum += argo[i];

  sum = sum % 256;  // modulo 256
  // Append sum to end of array
  // Set const part of checksum bit 10
  argo[10] = 0b00000010;
  argo[10] += sum << 2;  // Shift up 2 bits and append to byte 10
  argo[11] = sum >> 6;   // Shift down 6 bits and add in two LSBs of bit 11
}

void IRArgoAC::stateReset() {
  for (uint8_t i = 0; i < kArgoStateLength; i++) argo[i] = 0x0;

  // Argo Message. Store MSB left.
  // Default message:
  argo[0] = 0b10101100;  // LSB first (as sent) 0b00110101; //const preamble
  argo[1] = 0b11110101;  // LSB first: 0b10101111; //const preamble
  // Keep payload 2-9 at zero
  argo[10] = 0b00000010;  // Const 01, checksum 6bit
  argo[11] = 0b00000000;  // Checksum 2bit

  this->off();
  this->setTemp(20);
  this->setRoomTemp(25);
  this->setCoolMode(kArgoCoolAuto);
  this->setFan(kArgoFanAuto);
}

uint8_t* IRArgoAC::getRaw() {
  checksum();  // Ensure correct bit array before returning
  return argo;
}

void IRArgoAC::on() {
  // state = ON;
  ac_state = 1;
  // Bit 5 of byte 9 is on/off
  // in MSB first
  argo[9] = argo[9] | 0b00100000;  // Set ON/OFF bit to 1
}

void IRArgoAC::off() {
  // state = OFF;
  ac_state = 0;
  // in MSB first
  // bit 5 of byte 9 to off
  argo[9] = argo[9] & 0b11011111;  // Set on/off bit to 0
}

void IRArgoAC::setPower(bool state) {
  if (state)
    on();
  else
    off();
}

uint8_t IRArgoAC::getPower() { return ac_state; }

void IRArgoAC::setMax(bool state) {
  max_mode = state;
  if (max_mode)
    argo[9] |= 0b00001000;
  else
    argo[9] &= 0b11110111;
}

bool IRArgoAC::getMax() { return max_mode; }

// Set the temp in deg C
// Sending 0 equals +4
void IRArgoAC::setTemp(uint8_t temp) {
  if (temp < kArgoMinTemp)
    temp = kArgoMinTemp;
  else if (temp > kArgoMaxTemp)
    temp = kArgoMaxTemp;

  // Store in attributes
  set_temp = temp;
  // offset 4 degrees. "If I want 12 degrees, I need to send 8"
  temp -= 4;
  // Settemp = Bit 6,7 of byte 2, and bit 0-2 of byte 3
  // mask out bits
  // argo[13] & 0x00000100;  // mask out ON/OFF Bit
  argo[2] &= 0b00111111;
  argo[3] &= 0b11111000;

  argo[2] += temp << 6;  // append to bit 6,7
  argo[3] += temp >> 2;  // remove lowest to bits and append in 0-2
}

uint8_t IRArgoAC::getTemp() { return set_temp; }

// Set the speed of the fan
void IRArgoAC::setFan(uint8_t fan) {
  // Set the fan speed bits, leave low 4 bits alone
  fan_mode = fan;
  // Mask out bits
  argo[3] &= 0b11100111;
  // Set fan mode at bit positions
  argo[3] += fan << 3;
}

uint8_t IRArgoAC::getFan() { return fan_mode; }

void IRArgoAC::setFlap(uint8_t flap) {
  flap_mode = flap;
  // TODO(kaschmo): set correct bits for flap mode
}

uint8_t IRArgoAC::getFlap() { return flap_mode; }

uint8_t IRArgoAC::getMode() {
  // return cooling 0, heating 1
  return ac_mode;
}

void IRArgoAC::setCoolMode(uint8_t mode) {
  ac_mode = 0;  // Set ac mode to cooling
  cool_mode = mode;
  // Mask out bits, also leave bit 5 on 0 for cooling
  argo[2] &= 0b11000111;

  // Set cool mode at bit positions
  argo[2] += mode << 3;
}

uint8_t IRArgoAC::getCoolMode() { return cool_mode; }

void IRArgoAC::setHeatMode(uint8_t mode) {
  ac_mode = 1;  // Set ac mode to heating
  heat_mode = mode;
  // Mask out bits
  argo[2] &= 0b11000111;
  // Set heating bit
  argo[2] |= 0b00100000;
  // Set cool mode at bit positions
  argo[2] += mode << 3;
}

uint8_t IRArgoAC::getHeatMode() { return heat_mode; }

void IRArgoAC::setNight(bool state) {
  night_mode = state;
  if (night_mode)
    // Set bit at night position: bit 2
    argo[9] |= 0b00000100;
  else
    argo[9] &= 0b11111011;
}

bool IRArgoAC::getNight() { return night_mode; }

void IRArgoAC::setiFeel(bool state) {
  ifeel_mode = state;
  if (ifeel_mode)
    // Set bit at iFeel position: bit 7
    argo[9] |= 0b10000000;
  else
    argo[9] &= 0b01111111;
}

bool IRArgoAC::getiFeel() { return ifeel_mode; }

void IRArgoAC::setTime() {
  // TODO(kaschmo): use function call from checksum to set time first
}

void IRArgoAC::setRoomTemp(uint8_t temp) {
  temp -= 4;
  // Mask out bits
  argo[3] &= 0b00011111;
  argo[4] &= 0b11111100;

  argo[3] += temp << 5;  // Append to bit 5,6,7
  argo[4] += temp >> 3;  // Remove lowest 3 bits and append in 0,1
}