mgeppert/Tasmota
1
0
Fork 0
Code Issues Pull Requests 1 Actions Packages Projects Releases Wiki Activity
df7d266c75
Tasmota/tasmota/include/xdrv_75_dali.h

978 lines
107 KiB
C
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/*
xdrv_75_dali.h - DALI support for Tasmota
SPDX-FileCopyrightText: 2025 Theo Arends
SPDX-License-Identifier: GPL-3.0-only
*/
#ifdef USE_DALI
#ifndef _XDRV75_DALI_H_
#define _XDRV75_DALI_H_
/*-------------------------------------------------------------------------------------------*\
* DALI Address types - Send as first byte
\*-------------------------------------------------------------------------------------------*/
// Address types - Send as first byte
#define DALI_SHORT_ADDRESS0 0x00 // 0b00000000 0 - First short address
#define DALI_SHORT_ADDRESS1 0x02 // 0b00000010 1 - Next short address
// ...
#define DALI_SHORT_ADDRESS63 0x7E // 0b01111110 63 - Last short address
#define DALI_GROUP_ADDRESS0 0x80 // 0b10000000 0 - First group address
#define DALI_GROUP_ADDRESS1 0x82 // 0b10000010 1 - Next group address
// ...
#define DALI_GROUP_ADDRESS15 0x9E // 0b10011110 15 - Last group address
#define DALI_BROADCAST_DP 0xFE // 0b11111110 254 - Broadcast address
// Address selector bit - Send with first byte
#define DALI_SELECTOR_BIT 0x01 // Mark second byte as standard/extended command
/*-------------------------------------------------------------------------------------------*\
* DALI Commands for IEC62386 part 102 = Control gears - Send as first byte
\*-------------------------------------------------------------------------------------------*/
// Special commands - Send as first byte
#define DALI_102_TERMINATE 0xA1 // 256 - All special mode processes (like DALI_102_INITIALISE) shall be terminated.
#define DALI_102_SET_DTR0 0xA3 // 257 - Stores the data XXXX XXXX to the Data Transfer Register (Data Transfer Register 0).
// This is a broadcast command to set the value of the DTR0 register.
#define DALI_102_INITIALISE 0xA5 // 258 REPEAT - Sets the ballast to the INITIALISE status for 15 minutes. Commands 167 to 189 are enabled only for a ballast in this status.
// This command shall start or re-trigger a timer for 15 minutes; the addressing commands 167..189 shall only be processed within this period.
// All other commands shall still be processed during this period.
// This time period shall be aborted with the "DALI_102_TERMINATE" command.
// Ballasts shall react as follows:
// - if broadcast is True then all ballasts shall react
// - if broadcast is False and address is None then ballasts without a short address shall react
// - if broadcast is False and address is an integer 0..63 then ballasts with the address supplied shall react
#define DALI_102_RANDOMISE 0xA7 // 259 REPEAT - Generates a random address.
// The ballast shall generate a new 24-bit random address. The new random address shall be available within a time period of 100ms.
#define DALI_102_COMPARE 0xA9 // 260 - Is the random address smaller or equal to the search address?
// The ballast shall compare its 24-bit random address with the combined search address stored in SearchAddrH, SearchAddrM and SearchAddrL.
// If its random address is smaller or equal to the search address and the ballast is not withdrawn then the ballast shall generate a query "YES".
#define DALI_102_WITHDRAW 0xAB // 261 - Excludes ballasts for which the random address and search address match from the Compare process.
// The ballast that has a 24-bit random address equal to the combined search address stored in SearchAddrH, SearchAddrM and SearchAddrL
// shall no longer respond to the compare command.
// This ballast shall not be excluded from the initialisation process.
#define DALI_102_PING 0xAD // 262 - DALI-2 Ignores in the ballast.
// Transmitted at 10 minute intervals by single master application controllers (that cannot perform collision detection) to indicate their presence.
// Ignored by control gear.
#define DALI_102_RESERVED263 0xAF // 263 - [Reserved]
#define DALI_102_SEARCHADDRH 0xB1 // 264 - Specifies the higher 8 bits of the search address.
#define DALI_102_SEARCHADDRM 0xB3 // 265 - Specifies the middle 8 bits of the search address.
#define DALI_102_SEARCHADDRL 0xB5 // 266 - Specifies the lower 8 bits of the search address.
#define DALI_102_PROGRAM_SHORT_ADDRESS 0xB7 // 267 - The ballast shall store the received 6-bit address (AAA AAA) as a short address if it is selected.
// It is selected if:
// - the ballast's 24-bit random address is equal to the address in SearchAddrH, SearchAddrM and SearchAddrL
// - physical selection has been detected (the lamp is electrically disconnected after reception of command PhysicalSelection())
// If address is 255 ("MASK") then the short address shall be deleted.
#define DALI_102_VERIFY_SHORT_ADDRESS 0xB9 // 268 - Is the short address AAA AAA?
// The ballast shall give an answer 255 ("YES") if the received short address is equal to its own short address.
#define DALI_102_QUERY_SHORT_ADDRESS 0xBB // 269 - What is the short address of the ballast being selected?
// The ballast shall send the short address if the random address is the same as the search address or the ballast is physically selected.
// The answer will be in the format (address<<1)|1 if the short address is programmed, or "MASK" (0xff) if there is no short address stored.
#define DALI_102_PHYSICAL_SELECTION 0xBD // 270 - not DALI-2 Sets the ballast to Physical Selection Mode and excludes the ballast from the Compare process. (Excluding IEC62386-102ed2.0)
#define DALI_102_RESERVED191 0xBF // 271 - [Reserved]
// Extending special commands - Send as first byte
#define DALI_102_ENABLE_DEVICE_TYPE_X 0xC1 // 272 - Adds the device XXXX (a special device).
// This command shall be sent before an application extended command.
// This command can be processed without the use of the Initialise() command.
// This command shall not be used for device type 0.
#define DALI_102_SET_DTR1 0xC3 // 273 - Stores data XXXX into Data Transfer Register 1.
// This is a broadcast command to set the value of the DTR1 register.
#define DALI_102_SET_DTR2 0xC5 // 274 - Stores data XXXX into Data Transfer Register 2.
// This is a broadcast command to set the value of the DTR2 register.
#define DALI_102_WRITE_MEMORY_LOCATION 0xC7 // 275 - Write data into the specified address of the specified memory bank. (There is BW) (DTR(DTR0)：address, DTR1：memory bank number)
// This instruction will be ignored if the addressed memory bank is not implemented, or writeEnableState is DISABLED.
// If the instruction is executed then the control gear will write data into the memory location identified by DTR0 in bank DTR1 and return data as an answer.
// If the location is not implemented, above the last accessible location, locked or not writeable, the answer will be NO (-1).
// If the location addressed is below 0xff, then DTR0 will be incremented by 1.
#define DALI_102_WRITE_MEMORY_LOCATION_NO_REPLY 0xC9 // 276 - DALI-2 Write data into the specified address of the specified memory bank. (There is no BW) (DTR(DTR0)：address, TR1：memory bank number)
// This instruction will be ignored if the addressed memory bank is not implemented, or writeEnableState is DISABLED.
// If the instruction is executed then the control gear will write data into the memory location identified by DTR0 in bank DTR1
// If the location is not implemented, above the last accessible location, locked or not writeable, the answer will be NO (-1).
// If the location addressed is below 0xff, then DTR0 will be incremented by 1.
#define DALI_102_RESERVED277 0xCB // 277 - [Reserved]
// ...
#define DALI_102_RESERVED349 0xFD // 349 - [Reserved]
/*-------------------------------------------------------------------------------------------*\
* DALI Commands for IEC62386 part 102 = Control gears - Send as second byte
\*-------------------------------------------------------------------------------------------*/
// Control commands - Send as second byte without repeat
#define DALI_102_OFF 0x00 // 0 - Turns off lighting (without fade).
#define DALI_102_UP 0x01 // 1 - Increases the lighting control level for 200 ms according to the Fade rate.
// No change if the arc power output is already at the "MAX LEVEL".
// If this command is received again while it is being executed, the execution time shall be re-triggered.
// This command shall only affect ballasts with burning lamps.
// No lamp shall be ignited with this command.
#define DALI_102_DOWN 0x02 // 2 - Decreases the lighting control level for 200 ms according to the Fade rate.
// No change if the arc power output is already at the "MIN LEVEL".
// If this command is received again while it is being executed, the execution time shall be re-triggered.
// Lamp shall not be switched off via this command.
#define DALI_102_STEP_UP 0x03 // 3 - Increments the lighting control level (without fade).
// No change if the arc power output is already at the "MAX LEVEL".
// This command shall only affect ballasts with burning lamps. No lamp shall be ignited with this command.
#define DALI_102_STEP_DOWN 0x04 // 4 - Decrements the lighting control level (without fade).
// No change if the arc power output is already at the "MIN LEVEL".
// Lamps shall not be switched off via this command.
#define DALI_102_RECALL_MAX_LEVEL 0x05 // 5 - Maximizes the lighting control level to "MAX LEVEL" (without fade).
// If the lamp is off it shall be ignited with this command.
#define DALI_102_RECALL_MIN_LEVEL 0x06 // 6 - Minimizes the lighting control level to "MIN LEVEL" (without fade)
// If the lamp is off it shall be ignited with this command.
#define DALI_102_STEP_DOWN_AND_OFF 0x07 // 7 - Decrements the lighting control level and turns off lighting if the level is at the minimum (without fade).
#define DALI_102_ON_AND_STEP_UP 0x08 // 8 - Increments the lighting control level and turns on lighting if lighting is off (with fade).
#define DALI_102_DIRECT_ARC_POWER_CONTROL 0x09 // 9 Deprecated - Enable DAPC Sequence
// Indicates the start of a command iteration of DAPC(level) commands.
// The control gear shall temporarily use a fade time of 200ms while the command iteration is active independent of the actual fade/extended fade time.
// The DAPC sequence shall end if 200ms elapse without the control gear receiving a DAPC(level) command.
// The sequence shall be aborted on reception of an indirect arc power control command.
// value 0 - Off
// value minLevel...maxLevel
// value 255 - Retain current level
#define DALI_102_GO_TO_LAST_ACTIVE_LEVEL 0x0A // 10 - DALI-2 Adjusts the lighting control level to the last light control level according to the Fade time.
#define DALI_102_CONTINUOUS_UP 0x0B // 11 - DALI-2 Dim up using the set fade rate.
// TargetLevel shall be set to maxLevel and a fade shall be started using the set fade rate. The fade shall stop when maxLevel is reached.
#define DALI_102_CONTINUOUS_DOWN 0x0C // 12 - DALI-2 Dim down using the set fade rate.
// targetLevel shall be set to minLevel and a fade shall be started using the set fade rate. The fade shall stop when minLevel is reached.
#define DALI_102_RESERVED13 0x0D // 13 - [Reserved]
#define DALI_102_RESERVED14 0x0E // 14 - [Reserved]
#define DALI_102_RESERVED15 0x0F // 15 - [Reserved]
#define DALI_102_GO_TO_SCENE0 0x10 // 16 - Adjusts the lighting control level for Scene XXXX according to the fade time.
// If the ballast does not belong to this scene, the arc power level remains unchanged.
// If the lamp is off, it shall be ignited with this command.
// If the value stored for this scene is zero and the lamp is lit then the lamp shall be switched off by this command after the fade time.
// ...
#define DALI_102_GO_TO_SCENE15 0x1F // 31 - Adjusts the lighting control level for Scene XXXX according to the fade time.
// Configuration commands - Send as second byte with repeat
#define DALI_102_RESET 0x20 // 32 - The variables in the persistent memory shall be changed to their reset values.
// It is not guaranteed that any commands will be received properly within the next 300ms by a ballast acting on this command.
#define DALI_102_STORE_ACTUAL_LEVEL_IN_DTR0 0x21 // 33 - Store actual arc power level in the DTR (DTR0) without changing the current light intensity.
#define DALI_102_SAVE_PERSISTENT_VARIABLES 0x22 // 34 - DALI-2 Saves a variable in nonvolatile memory (NVM).
// All variables identified as non-volatile shall be stored to non-volatile memory.
// The control gear might not react to commands for up to 300ms after reception of this command.
// This command is recommended to be used typically after commissioning.
#define DALI_102_SET_OPERATING_MODE 0x23 // 35 - DALI-2 Set operatingMode to DTR0.
// If DTR0 does not correspond to an implemented operating mode, the command shall be ignored.
#define DALI_102_RESET_MEMORY_BANK 0x24 // 36 - DALI-2 Reset Memory Bank according to DTR0
// If DTR0 = 0 then all implemented and unlocked memory banks except memory bank 0 shall be reset.
// In all other cases, the memory bank identified by DTR0 will be reset provided it is implemented and unlocked.
// This command may cause control gear to react improperly to commands for up to 10s.
#define DALI_102_IDENTIFY_DEVICE 0x25 // 37 - DALI-2 Starts the identification state of the device. Start or restart a 10s timer.
// While the timer is running the device will run a procedure to enable an observer to distinguish the device from other devices in which it is not running.
// This procedure is manufacturer-dependent.
// Identification will be stopped immediately upon reception of any command other than Initialise, RecallMinLevel, RecallMaxLevel or IdentifyDevice.
#define DALI_102_RESERVED38 0x26 // 38 - [Reserved]
// ...
#define DALI_102_RESERVED41 0x29 // 41 - [Reserved]
#define DALI_102_SET_MAX_LEVEL 0x2A // 42 - Specifies the DTR data as the maximum lighting control level (maxLevel or "MAX LEVEL").
#define DALI_102_SET_MIN_LEVEL 0x2B // 43 - Specifies the DTR data as the minimum lighting control level (minLevel or "MIN LEVEL").
// If this value is lower than the "PHYSICAL MIN LEVEL" of the ballast, then store the "PHYSICAL MIN LEVEL" as the new "MIN LEVEL".
#define DALI_102_SET_SYSTEM_FAILURE_LEVEL 0x2C // 44 - Specifies the DTR data as the "SYSTEM FAILURE LEVEL".
#define DALI_102_SET_POWER_ON_LEVEL 0x2D // 45 - Specifies the DTR data as the "POWER ON LEVEL".
#define DALI_102_SET_FADE_TIME 0x2E // 46 - Specifies the DTR data as the "FADE TIME" in seconds.
// Formula T=0.5(sqrt(pow(2,DTR))) seconds
// With DTR0 in the range 1..15. If DTR0 is 0 then the extended fade time will be used.
// The fade time specifies the time for changing the arc power level from the actual level to the requested level.
// In the case of lamp off, the preheat and ignition time is not included in the fade time.
// The new fade time will be used after the reception of the next arc power command.
// If a new fade time is set during a running fade process, the running fade process is not affected.
// value 0 - < 0.707 s
// value 1 - 0.707 s
// value 2 - 1.000 s
// value 3 - 1.414 s
// value 4 - 2.000 s
// value 5 - 2.828 s
// value 6 - 4.000 s
// value 7 - 5.657 s
// value 8 - 8.000 s
// value 9 - 11.314 s
// value 10 - 16.000 s
// value 11 - 22.627 s
// value 12 - 32.000 s
// value 13 - 45.255 s
// value 14 - 64.000 s
// value 15 - 90.510 s
#define DALI_102_SET_FADE_RATE 0x2F // 47 - Specifies the DTR data as the "FADE RATE" in steps per second.
// Formula F = 506/(sqrt(pow(2,DTR))) steps/s
// With DTR in the range 1..15.
// The new fade time will be used after the reception of the next arc power command.
// If a new fade time is set during a running fade process, the running fade process is not affected.
// value 0 - not permitted
// value 1 - 357.796 steps/s
// value 2 - 253.000 steps/s
// value 3 - 178.898 steps/s
// value 4 - 126.500 steps/s
// value 5 - 89.449 steps/s
// value 6 - 63.250 steps/s
// value 7 - 44.725 steps/s
// value 8 - 31.625 steps/s
// value 9 - 22.362 steps/s
// value 10 - 15.813 steps/s
// value 11 - 11.181 steps/s
// value 12 - 7.906 steps/s
// value 13 - 5.591 steps/s
// value 14 - 3.953 steps/s
// value 15 - 2.795 steps/s
#define DALI_102_SET_EXTENDED_FADE_TIME 0x30 // 48 - DALI-2 Specifies the DTR data as the Extended Fade Time.
// If DTR0 > 0x4f then extendedFadeTimeBase and extendedFadeTimeMultiplier are both set to 0.
// Otherwise, extendedFadeTimeBase will be set to DTR0[3:0] and extendedFadeTimeMultiplier will be set to DTR0[6:4].
// If a new fade time is set during a running fade process, the running fade process is not affected.
// bit 0..3 - value 0..15 (E_DALIExtendedFadeTimeBase)
// bit 4..7 - 0 = Disabled (E_DALIExtendeFadeTimeMultiplier)
// 1 = Multiplier100ms
// 2 = Multiplier1s
// 3 = Multiplier10s
// 4 = Multiplier1min
#define DALI_102_RESERVED49 0x31 // 49 - [Reserved]
// ...
#define DALI_102_RESERVED63 0x3F // 63 - [Reserved]
#define DALI_102_SET_SCENE0 0x40 // 64 - Specifies the DTR data as Scene XXXX.
// The value 255 ("MASK") removes the ballast from the scene.
// ...
#define DALI_102_SET_SCENE15 0x4F // 79 - Specifies the DTR data as Scene XXXX.
#define DALI_102_REMOVE_FROM_SCENE0 0x50 // 80 - Deletes the Scene XXXX setting.
// This stores 255 ("MASK") in the specified scene register.
// ...
#define DALI_102_REMOVE_FROM_SCENE15 0x5F // 95 - Deletes the Scene XXXX setting.
#define DALI_102_ADD_TO_GROUP0 0x60 // 96 - Adds the ballast to Group XXXX.
// ...
#define DALI_102_ADD_TO_GROUP15 0x6F // 111 - Adds the ballast to Group XXXX.
#define DALI_102_REMOVE_FROM_GROUP0 0x70 // 112 - Deletes the ballast from Group XXXX.
// ...
#define DALI_102_REMOVE_FROM_GROUP15 0x7F // 127 - Deletes the ballast from Group XXXX.
#define DALI_102_SET_SHORT_ADDRESS 0x80 // 128 - Specifies the DTR data as a Short Address.
// The DTR must contain either:
// - (address<<1)|1 (i.e. 0AAAAAA1) to set a short address
// - 255 (i.e. 11111111) to remove the short address
#define DALI_102_ENABLE_WRITE_MEMORY 0x81 // 129 - Allows writing of the memory bank.
// writeEnableState shall be set to ENABLED.
// NB there is no command to explicitly disable memory write access; any command that is not directly involved with writing to
// memory banks will set writeEnableState to DISABLED.
// The commands that do not set writeEnableState to DISABLED are:
// - WriteMemoryLocation
// - WriteMemoryLocationNoReply
// - DTR0
// - DTR1
// - DTR2
// - QueryContentDTR0
// - QueryContentDTR1
// - QueryContentDTR2
#define DALI_102_RESERVED130 0x82 // 130 - [Reserved]
// ...
#define DALI_102_RESERVED143 0x8F // 143 - [Reserved]
// Query commands - Send as second byte
#define DALI_102_QUERY_STATUS 0x90 // 144 - Returns "STATUS INFORMATION"
// bit 0 - Status of the control gear. 0: OK.
// bit 1 - Lamp failure. 0: OK.
// bit 2 - Lamp power on. 0: OFF.
// bit 3 - Limit value error. 0: the most recently requested lamp power was either between MIN LEVEL and MAX LEVEL or was OFF.
// bit 4 - Fading completed: 0: fading finished. 1: fading active.
// bit 5 - Reset status. 0: no.
// bit 6 - Short address missing. 0: no.
// bit 7 - Power supply fault. 0: No. A reset or a lamp power control command has been received since the last switch-on.
#define DALI_102_QUERY_CONTROL_GEAR_PRESENT 0x91 // 145 - Returns bit0 - Is there a ballast that can communicate?
#define DALI_102_QUERY_LAMP_FAILURE 0x92 // 146 - Returns bit1 - Is there a lamp problem?
#define DALI_102_QUERY_LAMP_POWER_ON 0x93 // 147 - Returns bit2 - Is a lamp on?
#define DALI_102_QUERY_LIMIT_ERROR 0x94 // 148 - Returns bit3 - Is the specified lighting control level out of the range from the minimum to the maximum values?
#define DALI_102_QUERY_RESET_STATE 0x95 // 149 - Returns bit5 - Is the ballast in 'RESET STATE'?
#define DALI_102_QUERY_MISSING_SHORT_ADDRESS 0x96 // 150 - Returns bit6 - Does the ballast not have a short address?
#define DALI_102_QUERY_VERSION_NUMBER 0x97 // 151 - What is the corresponding IEC standard number?
// The high four bits of the answer represent the version number of the standard.
// IEC-60929 is version number 0; the 2009 version of IEC-62386 is version number 1.
// As of the 2014 version of IEC-62386, the answer shall be the content of memory bank 0 location 0x16.
// bit 0..3 - nMinorVersion
// bit 4..7 - nMajorVersion
#define DALI_102_QUERY_CONTENT_DTR0 0x98 // 152 - What is the DTR content?
#define DALI_102_QUERY_DEVICE_TYPE 0x99 // 153 - What is the device type?
// The device type affects which application extended commands the device will respond to.
// XXX this is updated for IEC 62386-102 and interacts with QueryNextDeviceType. In this case:
// - If the device does not implement any part 2xx device type then the response will be 254;
// - If the device implements one part 2xx device type then the response will be the device type number;
// - If the device implements multiple part 2xx device types then the response will be MASK (0xff).
// value 0 - Part 201: Standard device
// value 1 - Part 202: Device for emergency lighting.
// value 2 - Part 203: Device for discharge lamps.
// value 3 - Part 204: Device for low-voltage halogen lamps.
// value 4 - Part 205: Device for dimming incandescent lamps.
// value 5 - Part 206: Device for converting digital signals into DC signals.
// value 6 - Part 207: Device for light emitting diodes (LEDs).
// value 7 - Part 208: Device for switching functions.
// value 8 - Part 209: Device for color/color temperature control.
// value 9 - Part 210: Sequencer
// value 15 - Part 216: Load referencing
// value 16 - Part 217: Thermal gear protection
// value 17 - Part 218: Dimming curve selection
// value 19 - Part 220: Centrally supplied emergency operation
// value 20 - Part 221: Load shedding
// value 21 - Part 222: Thermal lamp protection
// value 23 - Part 224: Non-replaceable light sources
// value 49 - Part 250: Devices with integrated DALI bus power supply
// value 50 - Part 251: Further information and parameters for DALI control gears in memory bank 1
// value 51 - Part 252: Further parameters for the creation of an energy report
// value 52 - Part 253: Further parameters with diagnostic and maintenance information for DALI control gears
// value 53 - Part 254: Extended information for DALI control gears for emergency lighting
// value 254 - None or end
// value 255 - Multiple
#define DALI_102_QUERY_PHYSICAL_MINIMUM_LEVEL 0x9A // 154 - Return the physical minimum level for this device.
#define DALI_102_QUERY_POWER_FAILURE 0x9B // 155 - Ask whether the device has not received a "RESET" or arc power control command since the last power-on.
#define DALI_102_QUERY_CONTENT_DTR1 0x9C // 156 - Return the contents of DTR1.
#define DALI_102_QUERY_CONTENT_DTR2 0x9D // 157 - Return the contents of DTR2.
#define DALI_102_QUERY_OPERATING_MODE 0x9E // 158 - DALI-2 What is the Operating Mode?
#define DALI_102_QUERY_LIGHT_SOURCE_TYPE 0x9F // 159 - DALI-2 What is the Light source type (E_DALILightSourceType)
// "unknown" will typically be used in case of signal conversion, for example to 1-10v dimming
// "none" will be used where no light source is connected, for example a relay
// When the response is "multiple" then the light source types shall be placed into DTR0, DTR1 and DTR2.
// If there are exactly two light source types, DTR2 shall be "none". If there are more than three then DTR2 shall be MASK.
// value 0 = LowPressureFluorescent
// value 2 = HID
// value 3 = LowVoltageHalogen
// value 4 = Incandescent
// value 6 = LED
// value 7 = OLED
// value 252 = Other
// value 253 = Unknown (typicaly signal conversion like 1-10V dimming)
// value 254 = NoLightSource
// value 255 = Multiple (Type in DTR0, DTR1 and DTR2 (= none if two types, = 255 if > 3))
#define DALI_102_QUERY_ACTUAL_LEVEL 0xA0 // 160 - What is the "ACTUAL LEVEL" (the current lighting control level)?
// During preheating and if a lamp error occurs the answer will be 0xff ("MASK").
#define DALI_102_QUERY_MAX_LEVEL 0xA1 // 161 - What is the maximum lighting "MAX LEVEL" control level?
#define DALI_102_QUERY_MIN_LEVEL 0xA2 // 162 - What is the minimum lighting "MIN LEVEL" control level?
#define DALI_102_QUERY_POWER_ON_LEVEL 0xA3 // 163 - What is the "POWER ON LEVEL" (the lighting control level when the power is turned on)?
#define DALI_102_QUERY_SYSTEM_FAILURE_LEVEL 0xA4 // 164 - What is the "SYSTEM FAILURE LEVEL" (the lighting control level when a failure occurs)?
#define DALI_102_QUERY_FADE_TIME_FADE_RATE 0xA5 // 165 - What are the Fade time and Fade rate? (see 47 and 48)
// The fade time set by "DALI_102_SET_FADE_TIME" is in the upper four bits of the response.
// The fade rate set by "DALI_102_SET_FADE_RATE" is in the lower four bits of the response.
#define DALI_102_QUERY_MANUFACTURER_SPECIFIC_MODE 0xA6 // 166 - DALI-2 Query Manufacturer Specific Mode
// The answer shall be YES when operatingMode is in the range 0x80..0xff and NO otherwise.
#define DALI_102_QUERY_NEXT_DEVICE_TYPE 0xA7 // 167 - DALI-2 What is the next Device Type?
// If directly preceded by DALI_102_QUERY_DEVICE_TYPE and more than one device type is supported, returns the first and lowest device type number.
// If directly preceded by DALI_102_QUERY_NEXT_DEVICE_TYPE and not all device types have been reported, returns the next lowest device type number.
// If directly preceded by DALI_102_QUERY_NEXT_DEVICE_TYPE and all device types have been reported, returns 254.
// In all other cases returns NO (no response).
// Multi-master transmitters shall send the sequence DALI_102_QUERY_DEVICE_TYPE,DALI_102_QUERY_NEXT_DEVICE_TYPE,... as a transaction.
#define DALI_102_QUERY_EXTENDED_FADE_TIME 0xA8 // 168 - DALI-2 What is the Extended Fade Time?
// bit 0..3 - value 0..15 (E_DALIExtendedFadeTimeBase)
// bit 4..7 - 0 = Disabled (E_DALIExtendeFadeTimeMultiplier)
// 1 = Multiplier100ms
// 2 = Multiplier1s
// 3 = Multiplier10s
// 4 = Multiplier1min
#define DALI_102_QUERY_CONTROL_GEAR_FAILURE 0xA9 // 169 - DALI-2 Does a ballast have the abnormality (0 = No, 1 = Yes)?
// The answer shall be YES if controlGearFailure is TRUE and NO otherwise.
#define DALI_102_RESERVED170 0xAA // 170 - [Reserved]
// ...
#define DALI_102_RESERVED175 0xAF // 175 - [Reserved]
#define DALI_102_QUERY_SCENE0_LEVEL 0xB0 // 176 - Return the level set for scene 0, or 255 ("MASK") if the device is not part of the scene.
// ...
#define DALI_102_QUERY_SCENE15_LEVEL 0xBF // 191 - Return the level set for scene 15, or 255 ("MASK") if the device is not part of the scene.
#define DALI_102_QUERY_GROUPS_0_7 0xC0 // 192 - Return the device membership of groups 0-7 with group 0 in the least-significant bit of the response.
#define DALI_102_QUERY_GROUPS_8_15 0xC1 // 193 - Return the device membership of groups 8-15 with group 8 in the least-significant bit of the response.
#define DALI_102_QUERY_RANDOM_ADDRESS_H 0xC2 // 194 - What are the high 8 bits of the random address?
#define DALI_102_QUERY_RANDOM_ADDRESS_M 0xC3 // 195 - What are the middle 8 bits of the random address?
#define DALI_102_QUERY_RANDOM_ADDRESS_L 0xC4 // 196 - What are the low 8 bits of the random address?
#define DALI_102_READ_MEMORY_LOCATION 0xC5 // 197 - What is the memory location content (Uses DTR0 and DTR1)
// The query is ignored if the addressed memory bank is not implemented.
// If executed, the answer will be the content of the memory location identified by DTR0 in bank DTR1.
// If the addressed location is below 0xff, then DTR0 is incremented by 1.
#define DALI_102_RESERVED198 0xC6 // 198 - [Reserved]
// ...
#define DALI_102_RESERVED223 0xDF // 223 - [Reserved]
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 201 = DT0 - Send as second byte
* Standard device like fluorescent lamps
\*-------------------------------------------------------------------------------------------*/
#define DALI_201_DEVICE_TYPE 0
// Application extended query commands - Send as second byte
#define DALI_201_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 202 = DT1 - Send as second byte
* Device for emergency lighting
\*-------------------------------------------------------------------------------------------*/
#define DALI_202_DEVICE_TYPE 1
// Application extended query commands - Send as second byte
#define DALI_202_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 203 = DT2 - Send as second byte
* Device for discharge lamps excluding fluorescent lamps
\*-------------------------------------------------------------------------------------------*/
#define DALI_203_DEVICE_TYPE 2
// Application extended query commands - Send as second byte
#define DALI_203_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 204 = DT3 - Send as second byte
* Device for low-voltage halogen lamps
\*-------------------------------------------------------------------------------------------*/
#define DALI_204_DEVICE_TYPE 3
// Application extended query commands - Send as second byte
#define DALI_204_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 205 = DT4 - Send as second byte
* Device for dimming incandescent lamps
\*-------------------------------------------------------------------------------------------*/
#define DALI_205_DEVICE_TYPE 4
// Application extended configuration commands - Send as second byte with repeat
#define DALI_205_REFERENCE_SYSTEM_POWER 0xE0 // 224 - Reference System Power
// The control gear shall measure and store system power levels in order to detect load increase or load decrease.
// The measurement may take up to 15 minutes.
// Measured power levels will be stored in non-volatile memory, Commands received during the measuring period will be ignored except query commands and Terminate.
// The process will be aborted if DALI_102_TERMINATE is received.
#define DALI_205_SELECT_DIMMING_CURVE 0xE1 // 225 - Select Dimming Curve
// If DTR0 is 0 then selects the standard logarithmic curve
// If DTR0 is 1 then selects a linear dimming curve
// Other values of DTR0 are reserved and will not change the dimming curve.
// The setting is stored in non-volatile memory and is not cleared by the Reset command.
#define DALI_205_RESERVED226 0xE2 // 226 - [Reserved]
// ...
#define DALI_205_RESERVED237 0xED // 237 - [Reserved]
// Application extended query commands - Send as second byte
#define DALI_205_QUERY_DIMMING_CURVE 0xEE // 238 - Returns Dimming curve in use
// value 0 = Standard - Standard logarithmic dimming curve
// value 1 = Linear - Linear dimming curve
// value 255 = Unknown
#define DALI_205_QUERY_DIMMER_STATUS 0xEF // 239 - Returns dimmer status
// bit 0 - leading edge mode running
// bit 1 - trailing edge mode running
// bit 2 - reference measurement running
// bit 3 - None
// bit 4 - non-logarithmic dimming curve active
// bit 5..7 - Not used
#define DALI_205_QUERY_FEATURES 0xF0 // 240 - Return feature bytes. There are three bytes of feature information.
// Byte 1 is the reply to this command.
// bit 0 - load over-current shutdown can be queried
// bit 1 - open circuit detection can be queried
// bit 2 - detection of load decrease can be queried
// bit 3 - detection of load increase can be queried
// bit 4 - None
// bit 5 - thermal shutdown can be queried
// bit 6 - thermal overload with output level reduction can be queried
// bit 7 - physical selection supported
// Byte 2 is transferred to DTR0.
// bit 0 - temperature can be queried
// bit 1 - supply voltage can be queried
// bit 2 - supply frequency can be queried
// bit 3 - load voltage can be queried
// bit 4 - load current can be queried
// bit 5 - real load power can be queried
// bit 6 - load rating can be queried
// bit 7 - load current overload with output level reduction can be queried
// Byte 3 is transferred to DTR1.
// bit 0..1 - Dimming method
// value 0 = leading & trailing
// value 1 = leading only
// value 2 = trailing only
// value 3 = sine wave
// bit 2 - None
// bit 3 - non-logarithmic dimming curve can be selected
// bit 4..6 - None
// bit 7 - load unsuitable can be queried
#define DALI_205_QUERY_FAILURE_STATUS 0xF1 // 241 - Returns failure status. There are two bytes of failure information.
// Responds with byte 1 of the failure status information, and transfers byte 2 of the failure status into DTR1.
// Failure states which cause output level reduction shall only be reset by re-powering the control gear or by any command that causes the output to turn off.
// Failure states which cause shutdown shall only be reset by re-powering the control gear or using an optional reset switch on the control gear.
// Byte 1 is the reply to this command.
// bit 0 - load over-current shutdown
// bit 1 - open circuit detected
// bit 2 - load decrease detected
// bit 3 - load increase detected
// bit 4 - None
// bit 5 - thermal shutdown
// bit 6 - thermal overload with output level reduction
// bit 7 - reference measurement failed
// Byte 2 is transferred to DTR1.
// bit 0 - load not suitable for selected dimming method
// bit 1 - supply voltage out of limits
// bit 2 - supply frequency out of limits
// bit 3 - load voltage out of limits
// bit 4 - load current overload with output level reduction
// bit 5..7 - Not used
#define DALI_205_QUERY_DIMMER_TEMPERATURE 0xF2 // 242 - Returns the temperature of the dimmer with 1 degC resolution.
// Values of 0 to 254 represent temperatures of -40C to +214C.
// Below -40C, 0 is returned. Above 214C, 254 is returned. A value of 255 means "unknown".
// Control gear without this feature shall not react.
#define DALI_205_QUERY_RMS_SUPPLY_VOLTAGE 0xF3 // 243 - Returns the measured supply voltage.
// Values of 0 to 254 represent 0V to 508V RMS.
// Voltages above 508V RMS shall be returned as 254. A value of 255 means "unknown".
// Control gear without this feature shall not react.
#define DALI_205_QUERY_SUPPLY_FREQUENCY 0xF4 // 244 - Returns the supply frequency with 0.5Hz resolution.
// Values of 0 to 254 represent 0Hz to 127Hz.
// Frequencies above 127Hz are returned as 254. A value of 255 means "unknown".
// Control gear without this feature shall not react.
#define DALI_205_QUERY_RMS_LOAD_VOLTAGE 0xF5 // 245 - Returns the measured load voltage.
// Values of 0 to 254 represent 0V to 508V RMS.
// Voltages above 508V RMS shall be returned as 254. A value of 255 means "unknown".
// Control gear without this feature shall not react.
#define DALI_205_QUERY_RMS_LOAD_CURRENT 0xF6 // 246 - Returns the measured load current as a percentage of the rated load current given by the answer to QueryLoadRating, with 0.5% resolution.
// Values of 0 to 254 represent 0% to 127%.
// Higher currents shall be returned as 254. A value of 255 means "unknown".
// Control gear without this feature shall not react.
#define DALI_205_QUERY_REAL_LOAD_POWER 0xF7 // 247 - Returns the high byte of the real power supplied to the load. The low byte is transferred to DTR0.
// Values of 0 to 65534 represent powers from 0W to 16383.5W with a resolution of 0.25W.
// Powers above this range are returned as 65534. A value of 65535 means "unknown".
// Control gear without this feature shall not react.
#define DALI_205_QUERY_LOAD_RATING 0xF8 // 248 - Returns the maximum load current rating with 150mA resolution.
// Values of 0 to 254 represent 0A to 38.1A RMS.
// Currents above 38.1A shall be returned as 254. A value of 255 means "unknown".
// Control gear without this feature shall not react.
#define DALI_205_QUERY_REFERENCE_RUNNING 0xF9 // 249 - Asks if the ReferenceSystemPower measurement is running.
#define DALI_205_QUERY_REFERENCE_FAILED 0xFA // 250 - Asks if the reference measurement started by ReferenceSystemPower failed.
#define DALI_205_RESERVED251 0xFB // 251 - [Reserved]
// ...
#define DALI_205_RESERVED254 0xFE // 254 - [Reserved]
#define DALI_205_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 206 = DT5 - Send as second byte
* Device for converting digital signales into DC signals
\*-------------------------------------------------------------------------------------------*/
#define DALI_206_DEVICE_TYPE 5
// Application extended query commands - Send as second byte
#define DALI_206_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 207 = DT6 - Send as second byte
* Device for Light Emitting Diodes (LEDs)
* Variables
* Name Reset value Scope Size Comment
* --------------- --------------------------- ------------------------------------------- ------ ---------
* minFastFadeTime No change E_DALIFastFadeTime.T100ms 1 byte Read only
* ...
* E_DALIFastFadeTime.T700ms
* fastFadeTime E_DALIFastFadeTime.Disabled E_DALIFastFadeTime.Disabled,minFastFadeTime 1 byte
* ...
* E_DALIFastFadeTime.T700ms
* controlGearType No change 0...255 1 byte Read only
* features No change 0...255 1 byte Read only
* failureStatus No change 0...255 1 byte Read only
* dimmingCurve E_DALIDimmingCurve.Standard E_DALIDimmingCurve.Standard, 1 byte
* E_DALIDimmingCurve.Linear
\*-------------------------------------------------------------------------------------------*/
#define DALI_207_DEVICE_TYPE 6
// Application extended configuration commands - Send as second byte with repeat
#define DALI_207_REFERENCE_SYSTEM_POWER 0xE0 // 224 - The DALI control gear measures and stores the performance level of the system, in order to detect load increase and decrease.
#define DALI_207_ENABLE_CURRENT_PROTECTOR 0xE1 // 225 - Enables the current protection (deleted 2018).
#define DALI_207_DISABLE_CURRENT_PROTECTOR 0xE2 // 226 - Disables the current protection (deleted 2018).
#define DALI_207_SELECT_DIMMING_CURVE 0xE3 // 227 - Selects Dimming curve (see 238).
// If DTR0 is 0 then selects the standard logarithmic curve
// If DTR0 is 1 then selects a linear dimming curve
// Other values of DTR0 are reserved and will not change the dimming curve.
// The setting is stored in non-volatile memory and is not cleared by the Reset command.
#define DALI_207_SET_FAST_FADE_TIME 0xE4 // 228 - Sets the DTR0 of the data as Fast Fade Time (see 253).
#define DALI_207_RESERVED229 0xE5 // 229 - [Reserved]
// ...
#define DALI_207_RESERVED236 0xEC // 236 - [Reserved]
// Application extended query commands - Send as second byte
#define DALI_207_QUERY_GEAR_TYPE 0xED // 237 - Returns ‘GEAR TYPE’
// bit 0 - LED power supply integrated
// bit 1 - LED module integrated
// bit 2 - AC supply possible
// bit 3 - DC supply possible
// bit 4..7 - Reserve
#define DALI_207_QUERY_DIMMING_CURVE 0xEE // 238 - Returns Dimming curve in use (E_DALIDimmingCurve)
// value 0 = Standard - Standard logarithmic dimming curve
// value 1 = Linear - Linear dimming curve
// value 255 = Unknown
#define DALI_207_QUERY_POSSIBLE_OPERATING_MODE 0xEF // 239 - Returns ‘POSSIBLE OPERATING MODE’ (deleted 2018)
// bit 0 - PWM mode possible
// bit 1 - AM mode possible
// bit 2 - Output is current controlled
// bit 3 - High current pulse mode
// bit 4..7 - Reserve
#define DALI_207_QUERY_FEATURES 0xF0 // 240 - Returns ‘FEATURES’
// bit 0 - Short circuit detection can be queried
// bit 1 - Open circuit detection can be queried
// bit 2 - Detection of the load decrease can be queried
// bit 3 - Detection of the load increase can be queried
// bit 4 - Current protector is implemented and can be queried
// bit 5 - Thermal shutdown can be queried
// bit 6 - Reduction of the output level due to thermal overload can be queried
// bit 7 - Physical selection supported
#define DALI_207_QUERY_FAILURE_STATUS 0xF1 // 241 - Returns ‘FAILURE STATUS’
// bit 0 - Short circuit
// bit 1 - Open circuit
// bit 2 - Load decrease
// bit 3 - Load increase
// bit 4 - Current protector active
// bit 5 - Thermal shutdown
// bit 6 - Thermal overload with output level reduction
// bit 7 - Reference measurement failed
#define DALI_207_QUERY_SHORT_CIRCUIT 0xF2 // 242 - Returns bit0 short circuit of ‘FAILURE STATUS’ (deleted 2018)
#define DALI_207_QUERY_OPEN_CIRCUIT 0xF3 // 243 - Returns bit1 open circuit of ‘FAILURE STATUS’ (deleted 2018)
#define DALI_207_QUERY_LOAD_DECREASE 0xF4 // 244 - Returns bit2 load decrease of ‘FAILURE STATUS’
#define DALI_207_QUERY_LOAD_INDREASE 0xF5 // 245 - Returns bit3 load increase of‘FAILURE STATUS’
#define DALI_207_QUERY_CURRENT_PROTECTOR_ACTIVE 0xF6 // 246 - Returns bit4 current protector active of ‘FAILURE STATUS’ (deleted 2018)
#define DALI_207_QUERY_THERMAL_SHUTDOWN 0xF7 // 247 - Returns bit5 thermal shut down of ‘FAILURE STATUS’
#define DALI_207_QUERY_THERMAL_OVERLOAD 0xF8 // 248 - Returns bit6 thermal overload with light level reduction of ‘FAILURE STATUS’
#define DALI_207_QUERY_REFERENCE_RUNNING 0xF9 // 249 - Returns whether Reference System Power is in operation.
#define DALI_207_QUERY_REFERENCE_MEASURMENT_FAILED 0xFA // 250 - Returns bit7 reference measurement failed of ‘FAILURE STATUS’
#define DALI_207_QUERY_CURRENT_PROTECTOR_ENABLE 0xFB // 251 - Returns state of Curent protector (deleted 2018)
#define DALI_207_QUERY_OPERATING_MODE2 0xFC // 252 - Returns ‘OPERATING MODE’ (deleted 2018)
// bit 0 - PWM mode active
// bit 1 - AM mode active
// bit 2 - Output is current controlled
// bit 3 - High current pulse mode is active
// bit 4 - non-logarithmic dimming curve active
// bit 5..7 - Reserve
#define DALI_207_QUERY_FAST_FADE_TIME 0xFD // 253 - Returns set Fast fade time (E_DALIFastFadeTime)
// value 0 = Disabled
// value 4 = T100ms
// value 8 = T200ms
// value 9 = T225ms
// value 12 = T300ms
// value 16 = T400ms
// value 20 = T500ms
// value 24 = T600ms
// value 27 = T700ms
// value 255 = Unknown
#define DALI_207_QUERY_MIN_FAST_FADE_TIME 0xFE // 254 - Returns set Minimum fast fade time (variable minFastFadeTime)
#define DALI_207_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 208 = DT7 - Send as second byte
* Device for switching functions
\*-------------------------------------------------------------------------------------------*/
#define DALI_208_DEVICE_TYPE 7
// Application extended query commands - Send as second byte
#define DALI_208_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 209 = DT8 - Send as second byte
* Device for controlling colour and colour temperature
* Tc is expressed in MIREK and can vary from 1 Mirek (1000000 Kelvin) to 65534 Mirek (15.26 Kelvin)
* RGBWAF - Red, Green, Blue, White, Amber, Freely selectable color
\*-------------------------------------------------------------------------------------------*/
#define DALI_209_DEVICE_TYPE 8
// Application extended control commands - Send as second byte with repeat
#define DALI_209_SET_TEMPORARY_X_COORDINATE 0xE0 // 224 - Set temporary x-COORDINATE (Uses DTR0 (LSB) and DTR1 (MSB))
// The value is expressed in units of 1/65536. The maximum x-COORDINATE value is 0,99997
#define DALI_209_SET_TEMPORARY_Y_COORDINATE 0xE1 // 225 - Set temporary y-COORDINATE (Uses DTR0 (LSB) and DTR1 (MSB))
// The value is expressed in units of 1/65536. The maximum y-COORDINATE value is 0,99997.
#define DALI_209_ACTIVATE 0xE2 // 226 - Transfer buffered values of temporary registers to the lamp.
// It ends a running cross-fade and starts a new cross-fade for the respective color/color temperature.
#define DALI_209_X_COORDINATE_STEP_UP 0xE3 // 227 - The x-COORDINATE shall be set 256 steps higher (256/65536) immediately without fading.
// This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set.
// If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by
// the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’.
#define DALI_209_X_COORDINATE_STEP_DOWN 0xE4 // 228 - The x-COORDINATE shall be set 256 steps lower (256/65536) immediately without fading.
// This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set.
// If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by
// the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’.
#define DALI_209_Y_COORDINATE_STEP_UP 0xE5 // 229 - The y-COORDINATE shall be set 256 steps higher (256/65536) immediately without fading.
// This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set.
// If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by
// the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’.
#define DALI_209_Y_COORDINATE_STEP_DOWN 0xE6 // 230 - The y-COORDINATE shall be set 256 steps lower (256/65536) immediately without fading.
// This command shall only be executed when ‘Colour type xy-coordinate active’ bit, bit 4 of the ‘COLOUR STATUS’, is set.
// If the new colour value does not correspond to a colour attainable by the control gear, this shall be indicated by
// the ‘xy-coordinate colour point out of range’ bit, bit 0 of the ‘COLOUR STATUS’.
#define DALI_209_SET_TEMPORARY_COLOUR_TEMP_TC 0xE7 // 231 - Set temporary colour temperature Tc (Uses DTR0 (LSB) and DTR1 (MSB))
// The value is expressed in units of 1 Mirek.
// A value of 0 for Tc shall be ignored and therefore not stored in memory.
// NOTE Colour temperature TC can vary from 1 Mirek (1 000 000 K) to 65 534 Mirek (15,26 K).
#define DALI_209_COLOUR_TEMP_TC_STEP_COOLER 0xE8 // 232 - The ‘COLOUR TEMPERATURE TC’ shall be set 1 Mirek lower immediately without fading.
// This command shall only be executed when ‘Colour type colour temperature TC active’ bit, bit 5 of the ‘COLOUR STATUS’ is set.
// No change shall occur if ‘COLOUR TEMPERATURE TC’ is already at ‘COLOUR TEMPERATURE TC COOLEST’.
// If the new colour value does not correspond to a colour temperature attainable by the control gear, this shall be indicated by
// the ‘Colour temperature TC out of range’ bit, bit 1 of the ‘COLOUR STATUS’.
#define DALI_209_COLOUR_TEMP_TC_STEP_WARMER 0xE9 // 233 - The ‘COLOUR TEMPERATURE TC’ shall be set 1 Mirek higher immediately without fading.
// This command shall only be executed when ‘Colour type colour temperature TC active’ bit, bit 5 of the ‘COLOUR STATUS’ is set.
// No change shall occur if ‘COLOUR TEMPERATURE TC’ is already at ‘COLOUR TEMPERATURE TC WARMEST’.
// If the new colour value does not correspond to a colour temperature attainable by the control gear, this shall be indicated by
// the ‘Colour temperature TC out of range’ bit, bit 1 of the ‘COLOUR STATUS’.
#define DALI_209_SET_TEMPORARY_PRIMARY_N_DIMLEVEL 0xEA // 234 Deprecated - Set temporary primary N dimlevel (Uses DTR0 (LSB), DTR1 (MSB) and DTR2 (N))
// The value is expressed in units of 1/65536.
// The maximum ‘PRIMARY N DIMLEVEL’ value is 0,99997 and shall be interpreted on a linear scale.
// N depends on DTR2 and shall be in the range from 0 to 5 depending upon the available number of primaries.
// For any other value of DTR2 the command shall be ignored.
#define DALI_209_SET_TEMPORARY_RGB_DIMLEVEL 0xEB // 235 - Set temporary RGB dimlevel
// The data in the DTR shall be set as ‘TEMPORARY RED DIMLEVEL’.
// The data in DTR1 shall be set as ‘TEMPORARY GREEN DIMLEVEL’.
// The data in DTR2 shall be set as ‘TEMPORARY BLUE DIMLEVEL’.
#define DALI_209_SET_TEMPORARY_WAF_DIMLEVEL 0xEC // 236 - Set temporary WAF dimlevel
// The data in the DTR shall be set as ‘TEMPORARY WHITE DIMLEVEL’.
// The data in DTR1 shall be set as ‘TEMPORARY AMBER DIMLEVEL’.
// The data in DTR2 shall be set as ‘TEMPORARY FREECOLOUR DIMLEVEL’.
#define DALI_209_SET_TEMPORARY_RGBWAF_CONTROL 0xED // 237 - Set temporary RGBWAF control via DTR0
// The data in the DTR shall be stored as ‘TEMPORARY RGBWAF CONTROL’.
// bit 0 - output channel 0/Red; '0' = Unlinked, '1' = Linked
// bit 1 - output channel 1/Green; '0' = Unlinked, '1' = Linked
// bit 2 - output channel 2/Blue; '0' = Unlinked, '1' = Linked
// bit 3 - output channel 3/White; '0' = Unlinked, '1' = Linked
// bit 4 - output channel 4/Amber; '0' = Unlinked, '1' = Linked
// bit 5 - output channel 5/Freecolour; '0' = Unlinked, '1' = Linked
// bits 6..7 control type
// value 0 = Channel control
// value 1 = Colour control
// value 2 = Normalised colour control
// value 3 = reserved
// Bit 0 to bit 5 sets the appropriate output channel(s)/colour(s) linked or unlinked.
// Bit 6 and bit 7: The control type defines how the gear shall react to Arc Power Commands.
// The linked channels shall all be set to unlinked on any colour activation with colour type xy-coordinate, colour temperature TC or primary N.
// NOTE More than one channel can be linked at the same time
#define DALI_209_COPY_REPORT_TO_TEMPORARY 0xEE // 238 - Copy the contents of the variables with the color settings to the variables for the temporary color settings.
// Application extended configuration commands - Send as second byte with repeat
#define DALI_209_RESERVED239 0xEF // 239 - [Reserved]
#define DALI_209_STORE_TY_PRIMARY_N 0xF0 // 240 Deprecated - Store TY Primary N via DTR0/1/2
// The value is expressed in units of 0,5 lumen resulting in a possible range of TYmin = 0 lumen, to TYmax = 32767 lumen.
// A value of 65535 (“MASK”) means unknown.
// N depends on DTR2 and shall be in the range from 0 to 5 depending upon the available number of primaries.
// For any other value of DTR2 the command shall be ignored.
// A value of “MASK” means that this primary is undefined and calibration is needed.
#define DALI_209_STORE_XY_COORDINATE_PRIMARY_N 0xF1 // 241 Deprecated - Store XY coord primary channel N via DTR2
// The ‘TEMPORARY x-COORDINATE’ and the ‘TEMPORARY y-COORDINATE’, given by command 224 and command 225 shall be stored as ‘x-COORDINATE PRIMARY N’
// respectively ‘y-COORDINATE PRIMARY N’ of primary N given by the value of DTR2, and shall be in the range from 0 to 5 depending upon the available number of primaries.
// For any other value of DTR2 the command shall be ignored.
// A value of “MASK” in one of the “temporary colour value” values shall be stored which means that this primary is undefined and calibration is needed.
// NOTE 1 The intended use of this command is to store the actual xy-coordinate belonging to the primary. Any other use can lead to unexpected results (colours).
// NOTE 2 xy-coordinates outside the CIE 1931 colour space chromaticity diagram are not meaningful.
#define DALI_209_STORE_COLOUR_TEMP_TC_LIMIT 0xF2 // 242 - Set color temperature Tc limit in Mirek (Uses DTR0 (LSB), DTR1 (MSB) and DTR2 (TcLimit type))
// The value shall be stored in a variable defined by DTR2.
// For any other value of DTR2 the command shall be ignored.
// DTR2 = 0 - ColorTemperatureTcCoolest (lowest possible value but always equal to or warmer than the lowest possible physical value)
// DTR2 = 1 - ColorTemperatureTcWarmest (highest possible value but always equal to or cooler than the highest possible physical value)
// DTR2 = 2 - ColorTemperatureTcPhysicalCoolest (lowest possible physical value)
// DTR2 = 3 - ColorTemperatureTcPhysicalWarmest (highest possible physical value)
#define DALI_209_STORE_GEAR_FEATURES_STATUS 0xF3 // 243 - Set gear features / status (See 247) (Uses DTR0)
// The data in the DTR shall be interpreted as follows:
// bit 0 - Automatic Activation; '0' = No
// bit 1..7 - reserved; ‘0’ = No
// If bit 0, the ‘Automatic Activation’ bit, is set to 1, all arc power control commands except “ENABLE DAPC SEQUENCE” shall automatically trigger a colour transition.
// If the ‘Automatic Activation’ bit is set, bit 0 of the “GEAR FEATURES/STATUS” byte shall be set.
#define DALI_209_RESERVED244 0xF4 // 244 - [Reserved]
#define DALI_209_ASSIGN_COLOUR_TO_LINKED_COMMAND 0xF5 // 245 - Assign to linked channel via DTR0
// The data held in the DTR in the range 0 to 6 shall be used to assign any/all linked output channel(s) to the given colour.
// DTR0 = 0 - No colour assigned
// DTR0 = 1 - Red
// DTR0 = 2 - Green
// DTR0 = 3 - Blue
// DTR0 = 4 - White
// DTR0 = 5 - Amber
// DTR0 = 6 - Freecolour
// For any other value of the DTR the command shall be ignored.
// The linked channels are given by bit 0 to bit 5 held in “TEMPORARY RGBWAF CONTROL”.
// If “TEMPORARY RGBWAF CONTROL” holds “MASK” the channel assignment shall not be changed.
// The “TEMPORARY COLOUR SETTINGS” are set to “MASK” after use of this command.
#define DALI_209_START_AUTO_CALIBRATION 0xF6 // 246 - Start auto calibration
// The command shall start or re-trigger a 15 min timer. Bit 2 of “COLOUR STATUS” shall be set to “1” whilst this timer is running.
// When the timer stops the most recent colour type, colour value and arc power level shall be restored immediately
// Whilst the timer is running the control gear shall run a calibration procedure in order to measure the x-coordinate, y-coordinate and the TY-value of
// all supported primaries and bit 3 of “COLOUR STATUS” shall be set to “0”.
// While the calibration procedure is running, the control gear shall not react to any command except “TERMINATE”, “QUERY COLOUR STATUS” and “START AUTO CALIBRATION”.
// The "TERMINATE" command shall cause the procedure to be aborted and the timer to be stopped.
// If the calibration is successful then bit 3 of “COLOUR STATUS” shall be set to “1” and the timer shall be stopped.
// If the calibration is not successful (bit 3 of “COLOUR STATUS” is “0”) and the control gear is capable of recovering the
// last successful calibration data it shall do so.
// In this case bit 3 of “COLOUR STATUS” shall bet set to “1”.
// The capability to recover the last successful calibration data is a gear feature; see command 247.
// Auto calibration is a gear feature; see command 247. If this feature is not supported the control gear shall not react in any way.
// NOTE Due to the fact that the calibration process may take longer than 15 min, the control device should check the status of the auto calibration by
// command 248 ‘QUERY COLOUR STATUS’ periodically and re-trigger the calibration process timer by command 246 (START AUTO CALIBRATION) if necessary
// Application extended query commands - Send as second byte
#define DALI_209_QUERY_GEAR_FEATURES_STATUS 0xF7 // 247 - Returns gear features / status
// bit 0 - Automatic activation
// bit 1..5 - reserved
// bit 6 - Automatic calibration is supported
// bit 7 - Restoration of the automatic calibration is supported
#define DALI_209_QUERY_COLOUR_STATUS 0xF8 // 248 - Returns color status
// bit 0 - xy coordinate color point is outside the valid range.
// bit 1 - Color temperature Tc lies outside the valid range
// bit 2 - Automatic calibration is active.
// bit 3 - Automatic calibration was successful.
// bit 4 - Color representation xy-coordinate active.
// bit 5 - Color representation color temperature Tc active.
// bit 6 - Color representation primary N active.
// bit 7 - Color representation RGBWAF active.
#define DALI_209_QUERY_COLOUR_TYPE_FEATURES 0xF9 // 249 - Returns color type
// bit 0 - Supports color representation through xy coordinates.
// bit 1 - Supports color representation through color temperature Tc.
// bit 2..4 - Number of primary N colors supported. A value of 0 means that this color representation by primary colors is not supported.
// bit 5..7 - Number of RGBWAF channels supported. A value of 0 means that this color representation by RGBWAF is not supported.
#define DALI_209_QUERY_COLOUR_VALUE 0xFA // 250 - Returns color value (DTR0 = E_DALIColourValue) (MSB in response, Uses DTR0 for LSB).
// The answer depends on the DTR0 Value.
// Most responses involve a 16-bit number, in such cases the reponse is the MSB and LSB is loaded into DTR0.
// Answers corresponding to the DTR values related to an active colour type are only valid if the colour type of the requested colour value is
// active (see command 248) or if the control gear is capable of recalculating the requested colour value from the active colour type into a colour
// value of another colour type. If recalculation is not possible this shall be indicated by a value of “MASK” as answer.
// Querying the number of primaries, the x-coordinate, y-coordinate and TY of primary N shall be independent of the implemented colour type.
// If the control gear does not know the coordinates, or the primary is not there, the answer shall be “MASK”.
// E_DALIColourValue (DTR0):
// 0 - XCoordinate
// 1 - YCoordinate
// 2 - ColourTemperatureTC
// 3 - PrimaryNDimLevel0
// 4 - PrimaryNDimLevel1
// 5 - PrimaryNDimLevel2
// 6 - PrimaryNDimLevel3
// 7 - PrimaryNDimLevel4
// 8 - PrimaryNDimLevel5
// 9 - RedDimLevel
// 10 - GreenDimLevel
// 11 - BlueDimLevel
// 12 - WhiteDimLevel
// 13 - AmberDimLevel
// 14 - FreecolourDimLevel
// 15 - RGBWAFControl
// 64 - XCoordinatePrimaryN0
// 65 - YCoordinatePrimaryN0
// 66 - TYPrimaryN0
// 67 - XCoordinatePrimaryN1
// 68 - YCoordinatePrimaryN1
// 69 - TYPrimaryN1
// 70 - XCoordinatePrimaryN2
// 71 - YCoordinatePrimaryN2
// 72 - TYPrimaryN2
// 73 - XCoordinatePrimaryN3
// 74 - YCoordinatePrimaryN3
// 75 - TYPrimaryN3
// 76 - XCoordinatePrimaryN4
// 77 - YCoordinatePrimaryN4
// 78 - TYPrimaryN4
// 79 - XCoordinatePrimaryN5
// 80 - YCoordinatePrimaryN5
// 81 - TYPrimaryN5
// 82 - NumberOfPrimaries
// 128 - ColourTemperatureTcCoolest
// 129 - ColourTemperatureTcPhysicalCoolest
// 130 - ColourTemperatureTcWarmest
// 131 - ColourTemperatureTcPhysicalWarmest
// 192 - TemporaryXCoordinate
// 193 - TemporaryYCoordinate
// 194 - TemporaryColourTemperature
// 195 - TemporaryPrimaryNDimLevel0
// 196 - TemporaryPrimaryNDimLevel1
// 197 - TemporaryPrimaryNDimLevel2
// 198 - TemporaryPrimaryNDimLevel3
// 199 - TemporaryPrimaryNDimLevel4
// 200 - TemporaryPrimaryNDimLevel5
// 201 - TemporaryRedDimLevel
// 202 - TemporaryGreenDimLevel
// 203 - TemporaryBlueDimLevel
// 204 - TemporaryWhiteDimLevel
// 205 - TemporaryAmberDimLevel
// 206 - TemporaryFreecolourDimLevel
// 207 - TemporaryRgbwafControl
// 208 - TemporaryColourType
// 224 - ReportXCoordinate
// 225 - ReportYCoordinate
// 226 - ReportColourTemperatureTc
// 227 - ReportPrimaryNDimLevel0
// 228 - ReportPrimaryNDimLevel1
// 229 - ReportPrimaryNDimLevel2
// 230 - ReportPrimaryNDimLevel3
// 231 - ReportPrimaryNDimLevel4
// 232 - ReportPrimaryNDimLevel5
// 233 - ReportRedDimLevel
// 234 - ReportGreenDimLevel
// 235 - ReportBlueDimLevel
// 236 - ReportWhiteDimLevel
// 237 - ReportAmberDimLevel
// 238 - ReportFreecolourDimLevel
// 239 - ReportRgbwafControl
// 240 - ReportColourType
// If, for colour type RGBWAF, more output channels are assigned to one colour (Red, Green, Blue, White, Amber or Freecolour) and the actual levels
// of these output channels are different the answer to that query shall be “MASK”.
// For all other DTR values and for unsupported colour types no answer shall be sent and neither DTR1 nor the DTR shall be changed.
// NOTE 1 The actual level of an output channel can be queried by linking only this output channel and sending QUERY ACTUAL LEVEL.
// NOTE 2 A control device should always use command 160 (“QUERY ACTUAL LEVEL”) to update the report colour setting before querying it.
// NOTE 3 A value of “MASK” for any of “x-COORDINATE PRIMARY N”, “y-COORDINATE PRIMARY N” or “TY PRIMARY N” means that this primary is
// undefined and calibration is needed.
#define DALI_209_QUERY_RGBWAF_CONTROL 0xFB // 251 - RGBWAFControl contains further information about the assignment between output channel and color.
// bit 0 - Output channel 0 / red
// bit 1 - Output channel 1 / green
// bit 2 - Output channel 2 / blue
// bit 3 - Output channel 3 / white
// bit 4 - Output channel 4 / amber
// bit 5 - Output channel 5 / free selectable color
// bit 6..7 - 0 = channel control
// 1 = color control
// 2 = standardized color control
// 3 = reserved
// If an output channel/colour is not supported the appropriate bit shall read '0'
#define DALI_209_QUERY_ASSIGNED_COLOUR 0xFC // 252 - Returns the color assigned to the specified output channel (DTR0 = 0...5). If a non-existent channel number is specified, 255 (MASK) is returned. (Uses DTR0)
// Assigned colour for a given channel (as specified in DTR0). Refer to Command 252 "QUERY ASSIGNED COLOUR".
// Note that a response may indicate an assigned channel, or could also be "MASK" if the queried channel is not supported or is invalid.
// value 0 - No color assigned
// value 1 - Red
// value 2 - Green
// value 3 - Blue
// value 4 - White
// value 5 - Amber
// value 6 - Freely selectable color
#define DALI_209_RESERVED253 0xFD // 253 - [Reserved]
#define DALI_209_RESERVED254 0xFE // 254 - [Reserved]
#define DALI_209_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
/*-------------------------------------------------------------------------------------------*\
* DALI Application extended commands for IEC62386 part 210 = DT9 - Send as second byte
* Sequencer
\*-------------------------------------------------------------------------------------------*/
#define DALI_210_DEVICE_TYPE 9
// Application extended query commands - Send as second byte
#define DALI_210_QUERY_EXTENDED_VERSION_NUMBER 0xFF // 255 - The version number of the extended support.
// This command must be preceded by an appropriate DALI_102_ENABLE_DEVICE_TYPE_X command; if it is not then it will be ignored.
// Returns the version number of Part 2xx of IEC 62386 for the corresponding device type as an 8-bit number.
// Device type implementations must provide their own implementation of QueryExtendedVersionNumber using this mixin.
#endif // _XDRV75_DALI_H_
#endif // USE_DALI
Reference in New Issue View Git Blame Copy Permalink